30
SYSTEM CONFIGURATION (ZONES,
GENERAL
INFORMATION
RANGE
SUPERVISION
HOUSE
IDENTIFICATION
- 0. WIRELESS ZONE EXiANSlON -
(ZONES 1 THROUGH 63)
To expand the system using ALERT III wireless transmitters, a 4171XT-XM
dialer board, and a 4152LMB loop module must be installed, as described in
the ZONE EXPANSION MODULE section, and either one or two 4280s (or
4280-8% if only 8 wireless zones are required) must be connected to the
polling loop. Note that the 4280 draws 40mA current. If two receivers are
used, power for the second receiver should be taken from the auxiliary power
connection on the main Control.
NOTE: Unless stated otherwise, references to the 4280 Receiver represent
the 4280 andlor 4280-8 Receivers.
The 4280 RF receiver is a component of the VISTA XM system which
recognizes alarms, status messages and keypad control messages from
ALERT Ill transmitters at 345MHz (U.S.A.). These messages are processed
and relayed to the VISTA XM control panel via a P-wire polling loop. Using a
4280 allows expansion of up to 83 RF zones, plus a wireless keypad (5727).
.-\
The 4280 RF receiver can receive signals from wifeless transmitters within a
nominal range of 200 feet. This gives you greater expandability in installations
where hard wire might not be feasible.
Each transmitter (except 5701 and 5727) is supervfsed by a check-in signal
that is sent to the receiver at 70-90 minute intervals. If at least one Check-in is
not received from a transmitter within a programmed interval, the keypad will
display the transmitter number and ‘CHECK’ will be displayed. See the
section under PROGRAMMING RF OPTIONS. 1’31, for this selection.
Each transmitter (including 5701 and 5727) is also supervised for low battery
conditions, and will transmit a low battery signal to the 4280 when the battery
has approximately 30 days of life remaining. See PROGRAMMING RF
OPTIONS. 1’28, for LOW BATTERY AUDIBLE ANNUNCIATION selection.
NOTE: After replacing a low or dead battery, activate the transmitter and enter
the security code + OFF to clear its memory of the “Low Battev signal.
The 4280 itself is also supervised three ways:
1. If the cover of the 4280 is removed, an ALARM or TROUBLE will be
displayed depending upon the response programmed in fields 1’08 and
1’09.
2. If the connection is broken between the 4280 and the control panel, an
ALARM or -TROUBLE will be displayed depending on the response
programmed in programming fields 1’08 l? 1’09. This response is usually
that of a DAY/NIGHT or 24 hour type.
3. If, within a programmed interval of time, the 4280 does not hear from any
of its transmitters, an ALARM or TROUBLE will be displayed depending
on the response programmed in fields 1’08 8 1’09. The interval is
programmed in 1’30.
,,-.
-
The 4280 responds only to transmitters with the same house ID (DIP switch
programmable from 01-31). This prevents system interference from
transmitters in other nearby systems. To make sure you do not choose a
House ID that is in use nearby, put the system in the Sniffer Mode, which is
descrfbed later in this section.
;-.
ADEMCO’s VISTA
XM
SERIES TECHNICAL REFERENCE MANUAL
WWW.DIYALARMFORUM.COM
(8 Seiten)
(173 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern