ADEMCO Vista-128FB Einstellungsanleitung PDF herunterladen (Seite 71)

Section 4 – Programming

4-9

• 2✳30 Enter 1 to enable the Alpha Pager Module.

• 2✳31 - 2✳88 Paging service parameters. The

events (e.g., field 2*39) must be programmed

for the pager to work.

Fields for programming the delay times (e.g.

2*36 and 2*37 for pager 1) are relevant only

when using numeric format for the pager.

NOTE: For Event Log Report Codes program

System Group #2 in the #93 Menu Mode.

Programming for 4100SM

• ✳05 Enter 1 to print all zone faults/restores; enter

0 to print only events enabled in field 1✳70

• ✳14 Enter 1 if using Home Automation (cannot

use both serial printer and Home Automation)

• 1✳69 Not applicable

• 1✳70 Event Log Types (1=enable; 0=disable

• 1✳71 12/24-Hour Time Stamp (0=12 hr; 1=24 hr)

• 1✳72 Printer On-line (0=disable; 1=enable)

• 1✳73 Enter 0 for 1200 Baud Rate

NOTE: For Event Log Report Codes program

System Group #2 in the #93 Menu Mode.

Programming for Access Control

VistaKey

See the VistaKey-SK Installation and Setup Guide for

the detailed programming instructions.

VistaKey Dialer Enables

When the VistaKey is installed with an alarm system,

the system defaults are set so that the system does not

send reports to the central station. The programming

is accomplished in field 1∗35 for the following events:

• ACS Troubles - To enable or disable ACS trouble

reporting.

• ACS Bypasses - To enable or disable ACS bypass

reporting.

• ACS System - To enable or disable ACS system

reporting, (i.e., ACS module reset).

• ACS Alarms - To enable or disable ACS alarm

reporting.

• Dialer (Trace) - To enable or disable access

grant/denial events sent to the central station.

PassPoint

The PassPoint ACS can dedicate some of its inputs for

use as regular VISTA-128BP/VISTA-250BP hardwired

zones (the zone response type is ACS). The PassPoint

ACS can also utilize the control panel dialer for reports

to the central station.

PassPoint Dialer Events

All PassPoint ACS events can be sent to the VISTA-

128BP/VISTA-250BP dialer via the VGM. These events

will also be logged into the control’s event log. This is

enabled in the PassPoint ACS. See the PassPoint ACS

documentation for a detailed explanation.

Programming the VISTA Gateway Module

See the PassPoint ACS instructions to program the

VISTA Gateway Module.

Using ACS Zone Inputs

If the PassPoint ACS has uncommitted zones, these

may be used by the VISTA-128BP/VISTA-250BP as

hardwired zones. To program for ACS zone inputs,

perform the following steps:

Step Action

1 Enter Zone Programming in the #93 Menu

Mode.

2 Program this zone as any other zone. Indicate

the input type as ACS (10).

3 Enter the PassPoint ACS’s zone ID (00-31)

See Zone Programming in the Programming Guide for

a detailed explanation.

Access Control of an Entry/Exit Point

The control can send entry and exit requests to the

VistaKey or PassPoint ACS utilizing keypads and

button-type (BR) RF transmitters. A zone is

programmed with a response type 27 (Access Point)

and an appropriate input type (console, RF).

Using the Alpha Keypad

Step Action

1 Enter Zone Programming in the #93 Menu

Mode.

2 Program the zone with a response type 27

(Access Point).

3 Enter the access point number (00-31) of the

door.

4 Program whether this is an entry or exit

point.

5 Enter the partition number.

6 Enter the input type as CS (09).

7 Enter the keypad ECP address.

See Zone Programming in the Programming Guide for

a detailed explanation.

Using Wireless Keypads

Wireless keypads (5827 & 5827BD) can provide

another way of entering or exiting the premises. They

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 ... 146 147

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128FB Einstellungsanleitung Seite 71

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB