ADEMCO Vista-128FB Einstellungsanleitung PDF herunterladen (Seite 64)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

4-2

Press ✳94 to move to 3

page (fields 2✳00 - 2✳88);

press ✳99 to move back to 2

page

Entry Errors

• If an address is improperly entered, the keypad

displays “FC.”

• If a program entry is improperly entered (for

example, a larger number than is permitted), the

keypad display will go blank.

In either of the above cases, simply re-enter [✳] + the

correct field number and then enter the correct data.

Programming System-Wide Data Fields

Values for some programming fields are system-wide

(global), and some can be different for each partition

(partition-specific).

The partition-specific programming fields are

automatically skipped when programming the

global fields. If the system has only 1 partition,

the partition-specific fields

are not

automatically skipped.

To program system-wide data fields, perform the

following steps:

Step Action

Enter Program Mode: Installer Code + 8 0 0 0.

The following display appears:

Program Mode

✳Fill # View – 00

2 If the control has not been programmed before,

enter ✳97 to load factory defaults.

Press [✳] and enter the first field number to be

programmed (for example, ✳00, Installers

Code). Make the desired entry. When the

field is complete, the keypad beeps three times

and advances to the next field. If you do not

want to change the next field, press [✳] and

enter the next field number to be programmed.

First Page of fields

(✳00 - ✳90)

To change to the next page of fields, press ✳94.

To return to the previous page of fields, press

✳99.

Press ✳99 or ✳98 to exit Program Mode.

NOTE: If the number of digits that you enter in a data

field is fewer than the maximum permitted (for

example, a phone number), the keypad displays the

last entry and waits. To proceed, enter [✳] + the next

data field you wish to program.

Programming Partition-Specific Data Fields

To program partition-specific data fields once in

Program Mode, do the following:

Step Action

Enter Program Mode: Installer Code + 8 0

0 0.

Press ✳91, which will prompt you for the

partition number desired.

3 Enter a partition-specific field number (e.g.,

✳09) to begin programming.

When the first field’s entry is completed, the

next partition-specific field is automatically

displayed. When all partition-specific fields

are programmed, the system returns to the

global programming fields (page 1 fields).

4 Repeat this procedure for each partition in

the installation.

NOTE: To return to the global program fields before

finishing all fields, enter any global field number.

Programming Partition-Specific Fields

Press ✳91 to select a partition.

↓

↓↓

↓

Enter the partition to be programmed.

↓

↓↓

↓

Enter a partition-specific field number and make

entry.

↓

↓↓

↓

After partition-specific fields are programmed,

press ✳91 to select next partition.

Enter any global field number to return to the global

fields at any time.

#93 Menu Mode Programming

The #93 Menu Mode is an interactive mode through

which much of the system’s programming is done. In

this mode, there are “question and answer” prompts

that can be accessed once Data Field Program Mode

has been entered. These prompts require a 2-line

alpha keypad (6139/6160).

After programming all system-related programming

fields in the usual way, press #93 while still in

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 146 147

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128FB Einstellungsanleitung Seite 64

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB