ADEMCO Vista-128FB Einstellungsanleitung Seite 51
- Seite / 147
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Section 3 - Installing the Control
3-27
The VGM then reformats and retransmits this
information to the Main Logic Board, (MLB) on the
PassPoint ACS network bus.
U
L
Interfacing the VISTA-128BP/VISTA-250BP
with the PassPoint Access Control System via
the VISTA Gateway Module is not permissible
for UL installations.
Wiring the VISTA Gateway Module
The VISTA Gateway Module is connected between the
ECP bus (VISTA-128BP/VISTA-250BP keypad
terminals) and the network bus of the PassPoint
Access Control System. See Figure 3-32 for the proper
wiring connections.
}
ECHELON NETWORK
(PASSPOINT ACS)
YELLOW
RED
BLACK
PROM C
TRANSFORMER
4-PIN
KEYPAD
PLUG
}
TO
CONTROL’S
KEYPAD
TERMINALS
GREEN
Figure 3-32: Wiring the VISTA Gateway Module
Installing a 4100SM
The 4100SM is used to print event log reports to a
serial printer or to interface the control with a
computer equipped with Home Automation software.
When using the 4100SM, the system can
interface with either a serial printer or Home
Automation. It cannot do both.
NOTE: See SECTION 4: Programming for the
programming details when using the 4100SM.
Printer/Computer Configurations
Configure the serial printer or the Home Automation
computer as follows:
• 8 data bits, no parity, 1 stop bit
• 1200 baud
Connecting the 4100SM to a Serial Printer
To connect a serial printer using the 4100SM, refer to
Figure 3-33and perform the following steps:
Step
Action
1
Connect terminal 1 on the 4100SM to the
Violet wire on the 4142TR cable.
2
Connect terminal 6 on the 4100SM to the
Brown wire on the 4142TR cable.
3
Connect the 4142TR cable to J8 on the
control.
4
Connect terminals 8 and 7 of the 4100SM to
terminals 6 and 7 (aux. power (+) and (-)),
respectively of the control.
5
Connect the UL EDP Listed serial printer to
the 4100SM Interface Module.
The 4100SM Module is supplied with a 10-
foot RS232 cable. A longer cable can be used
if the VISTA-128BP/VISTA-250BP is
separated from the serial printer by more
than 10 feet, but the total cable length
should be less than 50 feet.
123456789
NU
J8 CONNECTOR
VIOLET
GREY
YELLOW
RED
GREEN
BROWN
BLUE
BLACK
IN
2
IN
3
G
R
O
U
N
D
O
U
T
5
O
U
T
6
G
R
O
U
N
D
G
R
O
U
N
D
PRINTER DTR
4142TR CABLE (SUPPLIED WITH 4100SM)
8
7
6
5
4
3
2
1
4100SM SERIAL MODULE
+ PWR
- (GND)
RXD
not used
not used
TXD
not used
DTR
BLUE WHITE
To TB6 Aux. Power (+)
(25mA current draw)
To TB7 Aux. Power (-)
USE GENDER CHANGER
SUPPLIED WITH 4100SM
IF PRINTER HAS DB25
MALE CONNECTOR
3M
Cable
Supplied with
4100SM
SERIAL PRINTER
SET FOR: 8 DATA BITS
EVEN PARITY
STOP BIT
300/1200 BAUD
4100SM JUMPERS
(CUT TO SET RESPECTIVE SIGNAL FLOATING)
COLOR FUNCTION PIN #
RED
BLUE
WHITE
CD
CTS
DSR
8
5
6
RED
4100SM-011-V0
Figure 3-33: 4100SM Using a Serial Printer
NOTE: See the 4100SM Installation Instructions for
details concerning the serial printer operation.
Connecting the 4100SM to a Home Automation
Computer
To connect the computer to the 4100SM, refer to
Figure 3-34 and perform the following steps:
Step
Action
1
Connect terminal 23 on the control panel to
terminal 3 on the 4100SM.
2
Connect terminal 6 on the 4100SM to the
Brown wire on the 4142TR cable.
3
Connect the 4142TR cable to J8 on the
control.
4
Connect terminals 8 and 7 of the 4100SM to
terminals 6 and 7 (aux. power (+) and (-)),
respectively of the control.
5
Connect the Home Automation computer
- Table of Contents 3
- ADEMCO LIMITED WARRANTY 5
- List of Figures 6
- General Description 9
- Features 10
- SECTION 2 13
- Theory of Partitioning 13
- Common Lobby Logic 13
- COMMON LOBBY 14
- Panel Linking 16
- 7 Bypass 19
- Installing the Control 21
- Installing the Keypads 23
- Installing External Sounders 24
- ALARM SOUNDER OUTPUT: 25
- 1-VDC - 13.8VDC 25
- 1.7A MAXIMUM 25
- Telephone Line Connections 26
- 2-WIRE SMOKE 28
- DETECTOR LOOP 28
- LATCHING TYPE GLASS 28
- BREAK DETECTORS 28
- Figure 3-11 29
- 333PRM-001-V0 30
- 333PRM-003-V0 31
- Installing RPM Devices 32
- POLLING LOOP 34
- Wireless Zone Expansion 35
- Device Programming 36
- Menu Mode 36
- Installing Output Devices 39
- Output Programming 40
- Programming 40
- 123456789 41
- Smoke Detector Reset 42
- Remote Keypad Sounder 42
- #93 Menu Mode 44
- ECP RADIO 46
- Installation and 49
- Setup Guide 49
- WEEKLY TESTING IS REQUIRED 50
- TO ENSURE PROPER OPERATION 50
- OF THIS SYSTEM 50
- Installing a 4100SM 51
- 4286_wiring-002-V1 53
- Figure 3-37 54
- Installing TeleSmart 55
- LOCAL INCOMING 57
- TO CONTROL'S 58
- TERMINALS 58
- Connecting the Transformer 59
- #93 Menu Mode Programming 64
- MAIN MENU 65
- OPTIONS 65
- Zone Number Designations 66
- Section 4 – Programming 67
- Zone Input Type Definitions 69
- Programming for 4100SM 71
- Programming for TeleSmart 72
- Data Field Descriptions 75
- Report Code Programming 77
- Programming Guide 85
- Scheduling Options 93
- Time Window Definitions 94
- Scheduling Menu Mode 96
- Time Windows 97
- Daily Open/Close Schedules 98
- Holiday Schedules 99
- Time-Driven Events 99
- Temporary Schedules 106
- User Scheduling Menu Mode 107
- Downloading Primer 109
- Section 7 – Downloading 111
- Scheduled Download 112
- Direct-Wire Downloading 112
- Telco Handoff 113
- Setting the Real-Time Clock 115
- User Access Codes 119
- Multiple Partition Access 120
- EXPLANATION 121
- Exiting the User Edit Mode 123
- Testing the System 125
- Trouble Conditions 127
- To the Installer 127
- Contacting Technical Support 128
- Regulatory Agency Statements 129
- Requirements 130
- Summary of System Commands 133
- Specifications 135
- APPENDIX D 137
- Index-D-2 141
- Index-D-4 143
- WARNING! 144
- ÊK5894V5%Š 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB
(5 Seiten)
(76 Seiten)
(24 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern