ADEMCO Vista-128FB Einstellungsanleitung PDF herunterladen (Seite 80)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

5-6

*51

Dual Reporting

0 = disable

1 = enable

If enabled, all reports are to be sent to both primary and secondary phone

numbers.

NOTE: If used with Split Reporting option 1 (1*34), alarms go to both primary

and secondary numbers, while all other reports go to secondary only. If used

with Split Reporting option 2, alarms go to both lines, open/close and test

messages go to secondary only, while all other reports go to primary.

*52

Standard/Expanded Reporting

Primary

0 = disable

1 = enable

This field has six entries as follows: Alarm, Restore, Bypass, Trouble,

Open/Close, Low Battery. If enabled, expanded reports are sent to the primary

phone number if low speed format is selected in field *45.

NOTE: Expanded overrides 4+2 format.

*53

Standard/Expanded Reporting

Secondary

0 = disable

1 = enable

This field has six entries as follows: Alarm, Restore, Bypass, Trouble,

Open/Close, Low Battery. If enabled, expanded reports are sent to the

secondary phone number if low speed format is selected in field *47.

NOTE: Expanded overrides 4+2 format.

*54

Unattended Mode

0 = disable

1 = enable

If enabled, the system automatically calls the downloader at programmed

intervals.

NOTE: The following fields must be programmed first: primary subscriber

account number – field *32; primary phone number – field *33; downloader

phone number – field *35. Or you can go into the Unattended Program Mode,

from normal operating mode, by entering Installer Code + [#] + [8] + [9].

*56

Dynamic Signaling Delay

Enter 00-15 times 15 seconds.

Select the time the panel should wait for acknowledgment from the first

reporting destination before it attempts to send a message to the second

destination (first and second destinations are determined in field

✳57).

NOTE: If the acknowledgment is received before the delay time expires, no

message is sent to the second destination.

*57

Dynamic Signaling Priority

0 = Primary Dialer

1 = Long Range Radio

Select the initial reporting path for central station messages.

*58

Long Range Radio Central

Station #1 Category Enable

0 = disable

1 = enable

This field has six entries as follows: Alarm, Trouble, Bypass, Open/Close,

System, Test. If enabled, the reports are sent to the primary subscriber ID of the

Long Range Radio.

*59

Long Range Radio Central

Station #2 Category Enable

0 = disable

1 = enable

This field has six entries as follows: Alarm, Trouble, Bypass, Open/Close,

System, Test. If enabled, the reports are sent to the secondary subscriber ID of

the Long Range Radio.

*79

Zone Type Restores for Zone

Types 1-8

0 = disable

1 = enable

This field has eight entries, one for each zone type. Select the zone types that

will send Restore reports.

*80

Zone Type Restores for Zone

Types 9, 10 and 16

0 = disable

1 = enable

This field has three entries, one for each zone type. Select the zone types that

will send Restore reports.

*83

First Test Report Time

Enter 00-07the for day (01 = Monday)

Enter 00-23 for the hour

Enter 00-59 for the minutes

Enter the day and time that the first Test report shall be transmitted. Enter 00 in

all locations if the Test report is to be sent immediately upon exiting. Enter 00 in

the day location if the report is to be sent at the next occurrence of the time that

is set.

FIELD

TITLE and DATA ENTRIES EXPLANATION

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 146 147

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128FB Einstellungsanleitung Seite 80

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB