ADEMCO Vista-128FB Einstellungsanleitung PDF herunterladen (Seite 16)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

2-4

Press [✴] + [0] or [✴] + [9] to return to the master

partition. Otherwise, if no keys are pressed for 2

minutes, the system automatically returns to the

master partition

The sounder on a Master keypad reflects the sound of

the most critical condition on all of the partitions. The

priority of the sounds, from most to least critical, is as

follows:

1. Pulsing fire alarm sounds

2. Steady burglar alarm sounds

3. Trouble sounds (rapid beeping)

Silence the sounder by pressing any key on the Master

keypad or a keypad on the partition where the

condition exists.

A Master keypad uses the same panics as

Partition 1. Master keypad panics are sent to

Partition 1, and will activate on Partition 1.

Therefore, panics must be programmed for

Partition 1.

Panel Linking

Up to eight VISTA-128BP/VISTA-250BP control panels

may be networked, enabling a user to control the

features of all control panels from a single location.

The panel linking bus supports an end-to-end network

length of up to 4,000 feet. This makes it ideal for

multi-building environments (e.g., shopping mall,

college campus, etc.).

Panel Linking is not permitted in UL

installations.

Panel linking requires a VA8200 Panel Link Module

(PLM) on each VISTA-128BP/VISTA-250BP. Users can

link (access other control panels) in any of three

different modes: Single-Partition, Single-Panel Mode;

Multi-Partition, Multi-Panel Mode; Multi-Panel View

Mode. These modes are described later in this section.

Each PLM connects to the ECP bus on the control

panel and communicates to each PLM via an RS-485

bus (3-wire twisted cable run) with a maximum wire-

run of 4000 feet end-to-end.

• Users 001-050 are the only users that can

perform panel linking and are automatically

assigned panel linking access when added

to the system.

• An alpha keypad must be used for panel

linking.

• The system may take up to 7 seconds to

respond to a command when in a panel

linking mode

NOTE: A user cannot access partitions or panels that

they have not been assigned to.

Panel Link Module Supervision

The Panel Link Module can be supervised for its

connection to the control panel. The module’s

supervisory zone is zone 8xx, where “xx” = the ECP

address of the PLM. You must program that zone with

response type 05 (Day/Night) in Zone Programming in

the #93 Menu Mode (refer to the Programming Guide

for detailed programming instructions). If you want to

report the supervisory failure to the central station

and/or to a paging service, the appropriate reporting

parameters for that zone must be programmed.

If you want the supervisory failure of PLM(s) on other

linked control panels to display on this control panel,

they must be programmed into Zone Programming in

the #93 Menu Mode with response type 14 in this

control panel (refer to the Programming Guide for

detailed programming instructions). The panel ID

number for each module must match the panel ID

number programmed in Device Programming of its

“host” VISTA-128BP/VISTA-250BP.

How to Use Panel Linking

Panel Linking can be used in any of three different

modes:

• Single-Partition, Single-Panel − displays status of

a partition on a remote control panel and allows

control of that remote control panel.

• Multi-Partition, Multi-Panel Mode − displays

status and allows arming/disarming of multiple

partitions at once on a remote control panel.

• Multi-Panel View Mode − displays status and

allows arming/disarming of multiple remote

control panels at a time.

NOTE: A user will not be able to access or view

partitions or panels that they have not been assigned

to.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 146 147

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128FB Einstellungsanleitung Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB