ADEMCO Vista-128FB Einstellungsanleitung PDF herunterladen (Seite 36)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

3-14

• Zones 988 and 990 are used to supervise the RF

reception of receivers 2 and 1, respectively. The

reception is supervised for two conditions:

1. The receiver goes “deaf” (doesn’t hear from

any transmitter) within a programmed

interval of time (defined by program field

1*30).

2. Proper RF reception is impeded (i.e., jamming

or other RF interference). The control checks

for this condition every 45 seconds.

A response type (05 Day/Night) must be

programmed for zones 990 (1

receiver) and

988 (2

receiver) for UL installations.

• The 5881ENHC receiver contains front and back

tampers that permit its use in commercial

burglary installations.

• You may only mount the 5881ENHC its own

plastic housing. Otherwise, the receiver constantly

reports a tamper condition.

• The control checks the receiver connections about

every 45 seconds. The receiver supervisory zone is

8 + 2-digit receiver device address (for example,

Device address 05 = supervisory zone 805).

NOTE: This zone must be programmed with a

response type (e.g., type 05 Day/Night Trouble)

before it supervise the connection to the receiver.

• Use two identical receivers to provide either a

greater area of coverage or redundant protection.

They must be set for different addresses.

• Any zone from 1 to 250 can be used as a 5800

Series wireless zone, with the exception of zone 64

(reserved for a wireless keypad).

RF System Installation Advisories

• Place the receiver in a high, centrally located area.

Do not place it on or near metal objects. This will

decrease the range and/or block transmissions.

• Install the RF receiver at least 10 feet from the

control panel or any keypads, to avoid interference

from the microprocessors in these units.

• If dual receivers are used:

a. They must be at least 10 feet from each other,

as well as from the control panel and remote

keypads.

b. Each receiver must be set to a different device

address. The receiver set to the lower address

is considered the 1

RF receiver for

supervisory purposes.

c. The House IDs must be the same.

d. Using two receivers does not increase the

number of transmitters the system can

support (249 zones using the 5881H, plus a

wireless keypad).

Installation and Setup of 5881 RF Receivers

Take note of the address you select for the RF

receiver, as this address must be enabled in

the system’s

Device Programming

in the

#93

Menu Mode

5881ENHC-001-V0

SCREW

Figure 3-19: Installing the 5881ENHC with Tamper

Protection

To install the 5881 RF receiver, perform the following

steps:

Step Action

1 Mount the receiver, following the advisories

stated previously.

2 Set the DIP switches in the receiver for the

address (01-07). See Figure 3-20.

Make sure the address setting is not

being used by another device (keypad,

relay module, etc.).

3 If installing a 5881ENHC, install a flat-head

screw (supplied) in the case tamper tab as

shown in Figure 3-19. When the receiver is

pried from the wall, the tamper tab will

break off and remain on the wall. This will

activate a tamper switch in the receiver and

cause generation of a tamper signal. Note

that this signal will also be generated when

the receiver’s front cover is removed.

4 Connect the receiver’s wire harness to the

keypad terminals (6, 7, 8, and 9). Plug the

connector at the other end of the harness

into the receiver.

5 Refer to the Installation Instructions

provided with the receiver for installations

regarding antenna mounting, etc.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 146 147

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128FB Einstellungsanleitung Seite 36

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB