ADEMCO Vista-128FB Einstellungsanleitung Seite 66
- Seite / 147
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
VISTA-128BP/VISTA-250BP Installation and Setup Guide
4-4
1 = YES 0 = NO 0
Following is a list of commands used while in the Menu Mode:
#93 Menu Mode Programming Commands
#93
Enters Menu Mode.
[✳]
Serves as [ENTER] key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO.
1
Press to answer YES.
00, or 000+[✳]
Quits Menu Mode and goes back to Data Field Programming Mode, if entered at first prompt of each main menu option.
Zone Number Designations
The VISTA-128BP supports up to 128 zones, the
VISTA-250BP supports up to 250 zones, of hardwire,
polling loop and/or wireless protection, distributed
among up to 8 partitions. The following table lists the
zone numbers and the types of sensors that can be
used with each, and some alternate functions of the
zones.
Zone Function
1 2-wire Smoke Detectors (if used)
5 Audio Alarm Verification (if used)
7 Keyswitch (if used)
8 Latching-Type Glassbreak Detectors (if used)
1-9 Traditional Hardwired Zones
9 RS232 Input (if used)
1-250 5800 Series Wireless Devices
10-250 Polling Loop Devices
995
✳ + 1 Panic
996 # + 3 Panic
999
✳ + # Panic
Zone Defaults
Zone # Zone Type Zone # Zone Type
001 09 601-632 00
002 03 800-830 00
003 03 970 00
004** 04 988 00
005 03 990 00
006 03 992* N/A
007 03 995 00
008 03 996 00
009 03 997 05
010–250 00 999 06
NOTES:
* Zone 992 is the Duress zone. Programming of the zone
response type is not applicable. This zone requires only the
report code programming.
** Zone 004 is also defaulted with Auto-STAY enabled.
Zone Index
The zones are designated as follows:
ZONE #
RANGE
ZONE
FUNCTION
ACTUAL ZONE
001 – 250 Protection
zones
As indicated
601 – 632 Relay
Supervisory
Zones
6 + 2-digit Relay Number; e.g.,
Relay Number 03 is zone 603.
800 – 830 ECP Device
Supervisory
Zones
8 + 2-digit Device Address; e.g.,
Device Address 01 is zone 801.
VIP Module is zone 804 (Device
Address must be set to 4).
TeleSmart is zone 824 (Device
Address must be set to 24).
970, 988,
990, & 997
System
Supervisory
Zones
970: Bell Supervision
988: 2
nd
Wireless Receiver –
not receiving signals
990: 1
st
Wireless Receiver –
not receiving signals
997: Polling Loop (short circuit)
992, 995 –
999
Duress and
Keypad
Panics
992: Duress
995: 1 + ✳ panic (A key)
996: 3 + # panic (C key)
999: ✳ + # panic (B key)
Program supervisory zones with response type of 05.
Communication Defaults
*45 PRIMARY FORMAT [1] ADEMCO Contact ID
*46 LOW SPEED FORMAT (Prim) [0] ADEMCO Low Speed
*47 SECONDARY FORMAT [1] ADEMCO Contact ID
*48 LOW SPEED FORMAT (Sec.) [0] ADEMCO Low Speed
*49 CHECKSUM VERIFICATION [0] [0]
No checksum Primary Secondary
*50 SESCOA/RADIONICS SEL. [0] Radionics
*51 DUAL REPORTING [0] no
*52 STANDARD/EXPANDED REPORT FOR PRIMARY
[0] [0] [0] [0] [0] [0]
standard
Alarm Rstr Bypass Trbl Opn/Cls Low Bat
*53 STANDARD/EXPANDED REPORT FOR SECONDARY
[0] [0] [0] [0] [0] [0]
standard
- Table of Contents 3
- ADEMCO LIMITED WARRANTY 5
- List of Figures 6
- General Description 9
- Features 10
- SECTION 2 13
- Theory of Partitioning 13
- Common Lobby Logic 13
- COMMON LOBBY 14
- Panel Linking 16
- 7 Bypass 19
- Installing the Control 21
- Installing the Keypads 23
- Installing External Sounders 24
- ALARM SOUNDER OUTPUT: 25
- 1-VDC - 13.8VDC 25
- 1.7A MAXIMUM 25
- Telephone Line Connections 26
- 2-WIRE SMOKE 28
- DETECTOR LOOP 28
- LATCHING TYPE GLASS 28
- BREAK DETECTORS 28
- Figure 3-11 29
- 333PRM-001-V0 30
- 333PRM-003-V0 31
- Installing RPM Devices 32
- POLLING LOOP 34
- Wireless Zone Expansion 35
- Device Programming 36
- Menu Mode 36
- Installing Output Devices 39
- Output Programming 40
- Programming 40
- 123456789 41
- Smoke Detector Reset 42
- Remote Keypad Sounder 42
- #93 Menu Mode 44
- ECP RADIO 46
- Installation and 49
- Setup Guide 49
- WEEKLY TESTING IS REQUIRED 50
- TO ENSURE PROPER OPERATION 50
- OF THIS SYSTEM 50
- Installing a 4100SM 51
- 4286_wiring-002-V1 53
- Figure 3-37 54
- Installing TeleSmart 55
- LOCAL INCOMING 57
- TO CONTROL'S 58
- TERMINALS 58
- Connecting the Transformer 59
- #93 Menu Mode Programming 64
- MAIN MENU 65
- OPTIONS 65
- Zone Number Designations 66
- Section 4 – Programming 67
- Zone Input Type Definitions 69
- Programming for 4100SM 71
- Programming for TeleSmart 72
- Data Field Descriptions 75
- Report Code Programming 77
- Programming Guide 85
- Scheduling Options 93
- Time Window Definitions 94
- Scheduling Menu Mode 96
- Time Windows 97
- Daily Open/Close Schedules 98
- Holiday Schedules 99
- Time-Driven Events 99
- Temporary Schedules 106
- User Scheduling Menu Mode 107
- Downloading Primer 109
- Section 7 – Downloading 111
- Scheduled Download 112
- Direct-Wire Downloading 112
- Telco Handoff 113
- Setting the Real-Time Clock 115
- User Access Codes 119
- Multiple Partition Access 120
- EXPLANATION 121
- Exiting the User Edit Mode 123
- Testing the System 125
- Trouble Conditions 127
- To the Installer 127
- Contacting Technical Support 128
- Regulatory Agency Statements 129
- Requirements 130
- Summary of System Commands 133
- Specifications 135
- APPENDIX D 137
- Index-D-2 141
- Index-D-4 143
- WARNING! 144
- ÊK5894V5%Š 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB
(5 Seiten)
(76 Seiten)
(24 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern