ADEMCO Vista-128FB Einstellungsanleitung Seite 49
- Seite / 147
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Section 3 - Installing the Control
3-25
VA8201 ALPHA PAGER MODULE
AUX
PWR.
PARALLEL
PRINTER
PARALLEL
OUTPUT
SERIAL
OUTPUT
DATA/
POWER
TO PHONE
TO LINE
EARTH
GROUND
HOME AUTOMATION COMPUTER
TIP
RING
RJ31X
JACK
TIP
RING
INCOMING TELCO LINE
ANSWERING
MACHINE
CALLER ID
UNIT
PREMISES
CALLER ID UNIT,
ANSWERING
MACHINE, AND
PHONES
RED
BROWN
GRAY
GREEN
RED
BLACK
GREEN
RED
BLACK
GREEN
AUX
GND.
62627282930237
TIP RING
HANDSET
TIP RING
INCOMING
PHONE
CORD
(ZONE 9)
BROWN WIRE
FROM 4142 TR
TRIGGER CABLE
SPLICE
VA8201-SOC-V1
1 2 3 4 5 6 7 8 9
J8
BROWN
ORANGE
CONTROL PANEL
NOTE
WHEN USING THE VA8201, ZONE 9 CAN NO
LONGER BE USED AS A PROTECTION ZONE.
Figure 3-30: Wiring the Alpha Pager Module
Access Control Using VistaKey
The VistaKey is a single-door access control module
that, when connected to the alarm system, provides
access control to the protected premises. The VISTA-
128BP supports up to 8 modules, the VISTA-250BP
supports up to 15 VistaKey modules (15 access points).
DO NOT USE BOTH the VistaKey and a
PassPoint Access Control System on the same
alarm panel.
U
L
The VistaKey module contains three zones.
These zones should ONLY be used for access
control functions in UL installations. THESE
INPUT ZONES ARE NOT TO BE USED FOR
FIRE AND BURGLARY APPLICATIONS IN UL
INSTALLATIONS.
VistaKey Features
• Each VistaKey communicates with the VISTA-
128BP/VISTA-250BP via the V-Plex polling loop.
• In the event local power to the VistaKey is lost,
the VistaKey module provides backup monitoring
of the access point door via a built-in V-Plex device
that is powered solely from the polling loop. It is
programmed as a new type of V-Plex device as
part of the control’s V-Plex Device Programming.
A serial number label is affixed to the VistaKey
module for manual entry of its serial number.
• The VistaKey supports up to 500 cardholders.
• The addition and removal of VistaKey modules
from the system is easily accomplished via the
VISTA-128BP/VISTA-250BP keypad.
• All configurable options for each VistaKey are
accomplished via software, firmware, and
nonvolatile memory, eliminating the need for PC
board jumpers. The access point zone number (1-
15) is set via a user-friendly, 16-position rotary
switch.
• Each VistaKey provides one open-collector output
trigger (sink 12mA @ 12VDC).
Mounting and Wiring the VistaKey
For detailed instructions on how to install and
program the VistaKey, refer the
Installation and
Setup Guide
that accompanies the VistaKey-
SK.
To mount and wire the VistaKey module, perform the
following steps:
Step Action
1 Mount the VistaKey, door strike or mag lock,
and card reader.
2 Mount the door status monitor (DSM) and/or
request-to-exit (RTE) devices.
3 Using Figure 3-31 as a reference, connect the
card reader interface cable to TB3, making
the +5V or +12V connection last.
- Table of Contents 3
- ADEMCO LIMITED WARRANTY 5
- List of Figures 6
- General Description 9
- Features 10
- SECTION 2 13
- Theory of Partitioning 13
- Common Lobby Logic 13
- COMMON LOBBY 14
- Panel Linking 16
- 7 Bypass 19
- Installing the Control 21
- Installing the Keypads 23
- Installing External Sounders 24
- ALARM SOUNDER OUTPUT: 25
- 1-VDC - 13.8VDC 25
- 1.7A MAXIMUM 25
- Telephone Line Connections 26
- 2-WIRE SMOKE 28
- DETECTOR LOOP 28
- LATCHING TYPE GLASS 28
- BREAK DETECTORS 28
- Figure 3-11 29
- 333PRM-001-V0 30
- 333PRM-003-V0 31
- Installing RPM Devices 32
- POLLING LOOP 34
- Wireless Zone Expansion 35
- Device Programming 36
- Menu Mode 36
- Installing Output Devices 39
- Output Programming 40
- Programming 40
- 123456789 41
- Smoke Detector Reset 42
- Remote Keypad Sounder 42
- #93 Menu Mode 44
- ECP RADIO 46
- Installation and 49
- Setup Guide 49
- WEEKLY TESTING IS REQUIRED 50
- TO ENSURE PROPER OPERATION 50
- OF THIS SYSTEM 50
- Installing a 4100SM 51
- 4286_wiring-002-V1 53
- Figure 3-37 54
- Installing TeleSmart 55
- LOCAL INCOMING 57
- TO CONTROL'S 58
- TERMINALS 58
- Connecting the Transformer 59
- #93 Menu Mode Programming 64
- MAIN MENU 65
- OPTIONS 65
- Zone Number Designations 66
- Section 4 – Programming 67
- Zone Input Type Definitions 69
- Programming for 4100SM 71
- Programming for TeleSmart 72
- Data Field Descriptions 75
- Report Code Programming 77
- Programming Guide 85
- Scheduling Options 93
- Time Window Definitions 94
- Scheduling Menu Mode 96
- Time Windows 97
- Daily Open/Close Schedules 98
- Holiday Schedules 99
- Time-Driven Events 99
- Temporary Schedules 106
- User Scheduling Menu Mode 107
- Downloading Primer 109
- Section 7 – Downloading 111
- Scheduled Download 112
- Direct-Wire Downloading 112
- Telco Handoff 113
- Setting the Real-Time Clock 115
- User Access Codes 119
- Multiple Partition Access 120
- EXPLANATION 121
- Exiting the User Edit Mode 123
- Testing the System 125
- Trouble Conditions 127
- To the Installer 127
- Contacting Technical Support 128
- Regulatory Agency Statements 129
- Requirements 130
- Summary of System Commands 133
- Specifications 135
- APPENDIX D 137
- Index-D-2 141
- Index-D-4 143
- WARNING! 144
- ÊK5894V5%Š 147
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128FB
(5 Seiten)
(76 Seiten)
(24 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.260 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern