ADEMCO 4140XMPT2 Bedienungsanleitung Seite 20
- Seite / 132
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
– 20 –
The following table highlights the features of each receiver.
FEATURE 4280 series 4281 series 5881 series
Wiring Connects to polling
loop
Connects to
console lines
Connects to
console lines
House ID set via DIP switches programmed via #93
Menu Mode.
programmed via #93
Menu Mode.
Receiver Address Set by cutting blue
jumper in 2nd
receiver. Enabled
via fields 1*26 &
1*27.
Set via DIP
switches. Enabled
via #93 Device
Programming.
Set via DIP
switches. Enabled
via #93 Device
Programming.
Cover Removal Causes alarm or
trouble depending
on response type
assigned.
Does not cause
alarm or trouble.
Does not cause
alarm or trouble.
Go/No Go Mode Requires cover
removal.
Automatic upon
entering test mode.
Automatic upon
entering test mode.
Spatial Diversity No. Requires 2
receivers for
redundancy or to
expand area of
coverage.
Yes. Eliminates
nulls and voids. 2nd
receiver expands
coverage area or
provides additional
redundancy.
Yes. Eliminates
nulls and voids. 2nd
receiver expands
coverage area or
provides additional
redundancy.
Transmitter ID Set via DIP
switches.
Set via DIP
switches.
Serial numbers are
"learned" by the
system.
4280 Series Receiver
4280 is not recommended
for new installation; receiver
is scheduled to be
discontinued.
• Important: Note that if using two RF Receivers, one of them must be
powered from auxiliary power, so as not to exceed the 64mA polling loop
current rating.
• Set field 1*32 to 0.
• For more information regarding the 4280 installation, refer to the installation
instructions provided with the 4280.
• If using a 4280-8, only up to 8 zones can be enabled as RF zones. If more than
8 zones are enabled, the message "SET-UP ERROR" (or E8 on non-alpha
consoles) will be displayed.
• Refer to the maximum polling loop wire runs described in the POLLING LOOP
section when connecting 4280s to the polling loop.
IMPORTANT: The maximum combined polling loop run is 4000'. If using
shielded wire, the maximum is 2000'.
4281 Series Receiver • Set field 1*32 to 1.
• Using #93 Menu mode–Device Programming, select as RF device type.
• Set house ID via #93 Menu Mode.
• Set receiver's device address using its DIP switches. Lower numbered
address is primary receiver (supervisory fault ID 90, 91). Higher numbered
address is secondary receiver (receiver fault ID 88, 89).
• Important: 4281 microprocessor must have part number N5334Vx, where x is
any number. The microprocessor is located just above the DIP switch on the
PC board.
5881 Series Receiver • Set field 1*32 to 2.
• Using #93 Menu mode–Device Programming, select as RF device type.
• Set house ID via #93 Menu Mode (needed for 5827 keypad only).
• Set receiver's device address using its DIP switches. Lower numbered
address is primary receiver (supervisory fault ID 90, 91). Higher numbered
address is secondary receiver (receiver fault ID 88, 89).
- 4140XMPT2 1
- CONGRATULATIONS! 2
- TABLE OF CONTENTS 3
- INSTALLATION INSTRUCTIONS 6
- SUMMARY OF SYSTEM FEATURES 7
- SCHEDULING OVERVIEW 12
- BASIC 9 HARD-WIRED ZONES 15
- Wire Gauge Max. Length 17
- J7 CONNECTOR 25
- 4142TR CABLE 25
- 1 2 3 4 5 6 7 8 9 26
- IST OF START 29
- URN ON LIGHTS 29
- ELL OUTPUT 30
- TROBE LIGHT 30
- YSTEM STATUS INDICATORS 30
- ONFIRMATION OF ARMING DING 30
- NLOCK EXIT DOORS 31
- URN ON EMERGENCY LIGHTING 31
- OUNDING FOR WIRELESS KEYPAD 31
- Section 3 32
- REMOTE CONSOLES, SOUNDERS 32
- & PHONE CONNECTIONS 32
- Wire Gauge Maximum Length 33
- EXTERNAL SOUNDERS 34
- PHONE CONNECTIONS 34
- Section 4 35
- POWERING THE SYSTEM 36
- (total poll loop worksht) 37
- Section 7 39
- Section 8 41
- PROGRAMMING GUIDE 42
- 00-15; 00=no suppression 43
- RF Trans. Type 46
- Section 2 50
- INDEX TO PROGRAMMING FIELDS 53
- DATA FIELD DESCRIPTIONS 54
- (refer to #93 and 60
- — 61 — 61
- Selected Partitio 61
- Set of Fields 61
- — 63 — 63
- 2nd Page Fields 63
- ALPHA VOCABULARY 75
- CHARACTER (ASCII) CHART 75
- COMMUNICATION FORMATS 76
- Code Definition 78
- COMMUNICATION PROGRAMMING 79
- NOTES Note: Low Speed will 80
- Section 6 DOWNLOADING 85
- DIRECT WIRE DOWNLOADING 87
- INTRODUCTION TO SCHEDULING 88
- Note that 00 is 89
- #80 SCHEDULING MENU MODE 92
- Number (HH:MM) (HH:MM) 93
- Hol. Partition 94
- Mon/Day 1 2345678 94
- HOLIDAY NUMBER ? 99
- Action Codes: 100
- 01 RELAY GRP # ? 100
- GROUP ? 12345678 100
- ACCESS SCHED # ? 101
- MON A1 Window 1? 101
- MON A3 Window 2 ? 101
- Hol A1 Window 1 ? 101
- Hol A1 Window 2 ? 101
- #83 USER SCHEDULING MENU MODE 104
- SYSTEM OPERATION 105
- Section 1. SYSTEM OPERATION 106
- User 3 User 5 108
- Level 1 Level 4 108
- Master Oper B 108
- KEYPAD FUNCTIONS 111
- Part. 1 WHSE 112
- User 01 Auth.=1 112
- PRINTER DTR 114
- BYPASS EVENT LOG 115
- SYSTEM EVENT LOG 115
- DIP SWITCH POSITION 121
- 4275EX PIR 122
- 4194 REED CONTACT 122
- (SURFACE MOUNT) 122
- 4278EX PIR 122
- IMPORTANT 123
- SET SWITCHES WITH 123
- BATTERY REMOVED 123
- Section 6. SPECIFICATIONS 124
- WARNING! 130
- RINGER EQUIVALENCE: 0.7B 131
- © 1996 PITTWAY CORPORATION 132
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4140XMPT2
(88 Seiten)
(61 Seiten)
(132 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern