ADEMCO 4120XM Betriebsanweisung PDF herunterladen (Seite 63)

Using The Test

Mode

Doors and Windows

Motion Detectors

Smoke Detectors

Turn Off Test Mode

Armed System Test

After the installation is completed, the Security System should be thoroughly

tested as follows:

1. With the System in the disarmed state, check that all zones are intact. If

DISARMED - Press * to show faults (Alpha consoles) or NOT READY

(Fixed-word consoles) is displayed, press the [*] key to display the

descriptors of the faulted zone(s). Restore faulted zone(s) if necessary, so

that

●***DISARMED***/READY TO ARM (Alpha consoles) or READY (Fixed-

word consoles) is displayed.

2. Enter the security code and press the TEST key. The external sounder (if

used) should

sound for 3 seconds and then turn off (the system is operating

on the back-up battety only at this time).

NOTE 1. The system will not enter the Test mode if the battery voltage is too

low, if the battery is not connected, or if any communication

messages are waiting to be transmitted.

NOTE 2. As a reminder that the system is in the Test

mode, the Console will

sound a single beep

at 15-second intervals if no protection zones are

violated.

NOTE 3. In the Test mode, no alarm reports will be sent to the central station.

Also, the external sounder (if used) will not be activated.

Open and close each protected door and window in turn. Each action should

produce three beeps from the Console. The descriptor for each protection zone

will appear on the Console display.

Walk in front of any interior motion detectors. Listen for three beeps when the

detector senses movement. While it is activated, its descriptor will remain

displayed on the Console. Note that wireless PIRs will have a 3-minute lockout

between transmissions to conserve battery life (remove cover for walk test to

override the 3-minute lock-out).

Follow the test procedure provided by the manufacturer of each smoke deteotor

to ensure that all detectors are operational and are functioning properly.

NOTE: A 2-wire smoke detector display will not clear until the Test mode is

exited.

Enter the security code and press the OFF key.

Important! A message will be sent to the central station during the following

tests. Notify the central station that a test will be in progress.

NOTE: A display of “COMM. FAILURE” (Alpha consoles) or

“FC” (Fixed-Word

consoles) indicates a failure to communicate (no Kissoff by the receiver at the

central station after the maximum number of transmission attempts is tried). If

this occurs, verify that the phone line is connected, the correct report format is

programmed, etc.

1. Arm the system and fault one or more zones. Silence alarm sounder(s) each

time by entering the code and pressing OFF. Check that Entry/Exit delay

zones provide the assigned delay times.

2. Check the keypad-initiated alarms, if programmed in field *05, by pressing the

Panic key pairs [x] & [#], [1] & [*], and/or [3] & [#] or dedicated panic keys A,

B, and C, if present.

If the system has been programmed for audible emergency, the console will

emit

a loud, steady alarm sound. The word ALARM and a descriptor “99” will

be displayed for [*] and [#] (or key B), “95” for [1] and [*] (or key A), “96” for

[3] and [#] (or key C).

Silence the alarm by entering the security code and pressing OFF. If the

system has been programmed for silent panic, there will be no audible alarms

or displays. A report will be sent to the central station, however.

3. Notify the central station that all tests are finished and verify results with them.

-63-

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4120XM Betriebsanweisung Seite 63

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4120XM