ADEMCO 4120XM Betriebsanweisung PDF herunterladen (Seite 54)

1*O9 Response Type For Three 2-digit field entfies:89 (2nd Receiver),90 (lst Receiver),9l (lst Receiver).

Zones 89-91

For UL applications, use of 1 or 2 RF RCVRS requires enabling their respective

(See Field *O5 for

faults (88-91 ) as applicable (type 5).

response types)

88&90=

RCVR not receiving transmitter signals. 89 & 91 = RCVR not

responding, bad connection to panel.

1*1o.1*17 Not Used

1*18 Select Wireless For

Enter 1 to enable a zone as wireless, otherwise enter O for hard-wire zones. If

Zones 1-8

zones 1-8 are to be used as wired zones, be careful not to select those zones for

(See field 1

●25)

RF because they will then be ignored,

since the wireless option

takes

precedence over hard-wire zones.

NOTE: Only up to 8 wireless zones (4281M or H) or up to 4 wireless zones

(4281 L) maybe selected within the range of 1-83.

1*19 Select Wireless For

(See field 1*18)

Zones 9-16

1*2O Select Wireless For (See field1*18)

Zones 17-24

1●21 Select Wireless For (See field 1*18)

Zones 25-32

1●22 Select Wireless For

(See field 1*18)

Zones 33-40

1*23 Select Wireless For (See field 1*18)

Zones 41-48

1*24 Select Wireless For (See field 1•18)

Zones 49-56

1*25 Select Wireless For (See field 1

●18)

Zones 57-63

1●26 First RF Receiver

Enter 1 if first Receiver is installed. Enter O if no Receiver is installed.

Select (Q=no/1=yes)

1●27 Second RF Receiver

Enter 1 if 2nd 4281 Receiver is installed. Enter O if only

one or no Receiver is

Select (Q=no/1=yes)

installed, If

second Receiver is installed, set DIP switch on 4281 (see Fig. 2).

1●28 RF Transmitter Low

Enter O if audible beep and display annunciation upon RF transmitter low battery

Battery

condition is desired only in disarmed state. Enter 1 if audible beep and display is

Annunciation

desired in both armed and disarmed states. Must be 1 for UL.

(Qfl)

1,29 Transmitter LOW

Enter 1 if a trouble message for RF transmitter low battery conditions is to be

Battery Report

sent to the central station. Enter O if no report for transmitter low battery is

Enable

desired.

Note that a trouble message will be sent for a transmitter supervision

(Q=no/1 =yes)

failure independent of this selection. Must be”1” for UL.

1.30 RF Receiver

Enter the check-in monitoring interval in 2-hour increments; enter 02-15 (entry

Supervision Check-

times 2=4-30 hours). Failure of a receiver to receive any RF signal within the time

In Interval

entered will result in activation of the response type programmed for zone 90 for

(00; 02-1 5)

the first Receiver and zone 88 for the second

Receiver and their related

communication reports. Enter 00 to disable supervision. NOTES:

If a zero is

programmed, supervision of the RF receiver will be disabled (response types for

zones 88 and 90 are disabled). Default=6. Max. “6” (12 hr) for UL.

1●31 RF Transmitter Enter the check-in monitoring intetval in 2-hour increments; enter 02-15 (4-30

Check-In Interval

hours). Failure of an individual transmitter to send a supervision signal within the

(00; 02-15)

time entered will result in a trouble response and related communication repoti.

Entry 00 disables transmitter supervision. Max. “6” (12 hr) for UL. DefauIt=12.

-54-

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4120XM Betriebsanweisung Seite 54

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4120XM