ADEMCO 4120XM Betriebsanweisung PDF herunterladen (Seite 50)

●37 Download Command Eight single-digit field entries:

Enables

Dialer Shutdown, System Shutdown, Not Used (0), Remote Bypass, Remote

@=yes/ O=no)

Disarm, Remote Arm, Upload Program, Download Program.

See field 1●53 for Callback disable option. For UL installations, Upload &

Download must be enabled; all others must be disabled.

Each of the various remote (from the central station) functions can either be

enabled or disabled. Disabling a function means that the central station will not

be able to perform that function with respect to this system. Enter 1 to enable a

function, and O to disable a function.

For UL installations, all entries must be O.

●

38 Inhibit Bypass Of A Entering a zone number (01-31 only) prevents that zone from being bypassed by

Zone

the user. Enter 00 if this feature is not desired (all zones can be bypassed). This

(m 01-31)

selection does not affect fire zones, which can never be bypassed.

●39 Open/Close Reports

See field *4O

For Users 1-8

(l=yes/Q=no)

*4O

Open/Close Reports

Enter 1 for each

user which is to send open/close reports to the central station.

For Users 9-16

Note that user 7 must be enabled if either open/close reporting is desired for

(1=yes/ Q=no)

keyswitch arming, or if close reporting is desired for Quick Arm and Power

arm, or if open/close reporting is desired for remote arm/disarm via downloading.

Note that users 16-70 are sent as user 15

for traditional communication formats.

To receive all user codes, Ademco Contact ID

reporting must be used.

*41 EOLR Disable

Enter O if end-of-line resistors are to be used. Enter 1 if end-of-line resistors are

(Zones 2-8)

not to be used (normally closed loops that detect only an open and do not require

(O=EOLR/1= no EOLR) end-of-line resistors). Must be “O”for UL.

Note: You must enter “O” (EOLR usage) in this field if a remote keyswitch is

being used (also see field

●15).

●42 Dial Tone Pause

Enter the desired wait time for dial tone detection as follows: Enter single digit, O

(Q/1/2)

= 5 seconds; 1 = 11 seconds; or 2 = 30 seconds. Must be Ofor

UL.

*43 Dial Tone Detect

Enter 1 if true dial tone detection is desired. Enter Oif only a delay before dialing

(I=true tone/O=pause)

(same as programmed in field *42) is desired. The

latter may be necessary in

high-noise environment Telco networks where

noise can be confused with dial

tone, resulting in premature dialing.

●

44 Ring Detection Count

Only applicable if central station initiated downloading will be used. Enter 00 to

(B O1-15)

disable ring detection. Enter 01-14 for ring counts of 1-14. Enter 15 to select

mode that gets around telephone answering machines connected to the same

phone line. In the latter mode, the system upon hearing one ring followed by

nothing, will not answer but will ready itself to pick up the next incoming call

received within the next 30 seconds on the first ring (the downloader calling

again).

*45

Primary Format

Enter the appropriate number for the primary format as follows: O=Low Speed;

(Qfl1213

1=Contact ID; 2=Ademco High Speed; 3=Ademco Express

●46 Low Speed Format

Enter the appropriate value: O=Ademco Low Speed; 1=Sescoa/Radionics

(Primary) (Q/1)

●

47 Secondary Format

Enter the appropriate number for the secondary format: O=Low Speed; 1=Contact

(Q/1 /2f3)

ID; 2=Ademco High Speed; 3=Ademco Express

●48 Low Speed Format

Enter the appropriate value: O=Ademco Low Speed; 1=Sescoa/Radionics

(Secondary) (Q/l )

●49 Checksum Verification

Enter 1 to send a verification digit to validate the message at the receiver without

(Q= non = yes)

having to send two message rounds. NOTE: Selection applies to both primary

and secondary phone numbers, and is

valid for 3+1, 4+2, and Ademco High

Speed reports. Enter O if not desired.

-50-

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4120XM Betriebsanweisung Seite 50

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4120XM