ADEMCO Vista-128B PLUS Einstellungsanleitung PDF herunterladen (Seite 36)

– 36 –

STOP (STP):

The "STOP" programming determines when and under what conditions the device is de-activated. The

following options are available:

1). RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device de-activates

when all the zones in that list restore from a previous fault, trouble, or alarm condition. This occurs

regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" is

normally only used when a "ZONE LIST" is used to start the device.

2). ZONE TYPE/SYSTEM OPERATION (ZT). Instead of using a "RESTORE ZONE LIST," you can select

a specific zone (response) type or system operation action to de-activate the device.

If you choose a specific "ZONE TYPE," any zone of that response type that restores from a previous

alarm, trouble, or fault condition will cause the device to de-activate.

If you choose a "SYSTEM OPERATION," that operation causes the device to de-activate. The

different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Relays”

later in this section, and in the Programming Form.

3) PARTITION NO. (P). The device's "Stop" Zone Type/System Operation may be limited to an

occurrence on one partition (1-8), or on any partition (0).

The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the

“RESTORE/ZONE LIST” combination.

Output Devices Programming

From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. Press [0] (NO) to each menu option

until the "OUTPUT PGM?" prompt appears. Press [1] (YES).

While in this mode, press [✱] to advance to next screen. Press [#] to back up to the previous screen.

PROMPT

EXPLANATION

ENTER RELAY #

(00=QUIT) 01

Enter the relay (output device) identification number 01-96. This is a reference number only, used for

identification purposes. The actual module address and relay number on the module are programmed in the

last two prompts.

Press [✱] to continue.

02 A EV ZL ZT P

STT 0 0 00 00 0

Press [✱] to continue.

02 A ZL ZT P

STOP 0 00 00 0

The keypad displays a summary STOP screen.

Press [✱] to continue.

02 RELAY ACTION

NO RESPONSE 0

The Relay Action is the way in which the relay will respond when activated by the "start" event. Enter the

desired action for this relay as follows:

0=not used; 1=close for 2 secs.; 2=stay closed; 3=pulse on/off; 4= toggle on and off alternately

02 START EVENT

NOT USED 0

An output may be activated by an Event/Zone List combination, and/or by a Zone Type/System Operation.

For an Event/Zone List combination, enter the event code as follows:

0=not used; 1=alarm; 2=fault; 3=trouble

If you are not using a Zone List to activate the relay, enter 0.

Press [✱] to continue.

02 START: ZN LIST

A zone list is a set of zones that can be used to initiate the start or stop relay action. If a zone list is being

used to start this relay action, enter the zone list number, 1-15. If a zone list is not being used, enter 0.

Press [✱] to continue.

02 START: ZONE #

000

A specific zone can be used instead of or in addition to an Event/Zone List or Zone Type/System Operation

combination to start the relay action. Enter the 3-digit zone number.

Press [✱] to continue.

02 START: ZN TYPE

NO RESPONSE 00

A Zone Type/System Operation can be used instead of or in addition to an Event/Zone List combination or

a specific zone to start the relay action. If a Zone Type/System Operation is being used, enter the 2-digit

code as listed in the table that follows.

Press [✱] to continue.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 71 72

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128B PLUS Einstellungsanleitung Seite 36

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128B PLUS