ADEMCO Vista-128B PLUS Einstellungsanleitung PDF herunterladen (Seite 21)

– 21 –

PROMPT

EXPLANATION

Zn ZT P RC In L

010 03 1 10 RF

Enter all zone information except for Loop number, or press “C” to copy the zone information on this screen

from the last saved zone (including Loop).

ZT = Zone Type

P = Partition

RC = Report Code

In = Input Device Type

L = Loop number to which the sensor is connected.

NOTE: Pressing the [C] copies the zone information from the last saved zone, which includes the

input type. Verify this information is correct for this zone.

On this screen:

• Use the [A] key to move to the right.

• Use the [B] key to move to left and to back up to “ZT” field.

Press [✱] to accept the existing or newly-entered zone information.

ZN B M V A C E AD

010 − − 1 0 1 1 01

Enter the remainder of the zone’s information, or press the [C] key to copy the zone attributes on this screen

from the last saved zone.

B = Not Applicable

M = Not Applicable

V = V-plex Relay? (only used if “In” = 6)

AC = Access Point (only used if ZT = 27, 29 or In = 6, 11, 12, 13)

E = Entry or Exit? (only used if ZT = 27)

AD = Address (only used if “In” = 9 or 10)

If “In” = 9, enter the Device Address

If “In” = 10, enter the PassPoint Zone Number

NOTE: Pressing the [C] copies the zone attributes from the last saved zone. Verify the attributes for

this zone are correct.

On this screen:

• Use the [A] key to move to the right.

• Use the [B] key to move to left and to back up to “V” field.

Press [✱] to accept existing information.

010 INPUT S/N: L

A XXX-XXXX

If you entered RM, RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary

screen for the next zone displays.

Enter the 7-digit serial number, using one of the following methods:

a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and

release the button, wait approximately 4 seconds, then press and release the button a second time.

b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad.

Then press the [✱] key, the cursor will move to the “L” position. You can edit the loop number, if

necessary. When the loop number is acceptable, press [✱].

c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several

input loops).

Remember, you can use the [A] key to move to the right or the [B] key to move to the left.

You can also use the [#] key to back up without saving.

010 INPUT S/N: L

A022-4064 1

Press [✱] to accept the serial number and advance to the “L” position (if method “a” or “c” was used), then

enter the loop number.

If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before

pressing [✱] to save

The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will

emit a single long beep, and display the serial number along with a “?” for the loop number, allowing you to

re-enter the correct loop number.

010 INPUT S/N: L

A000-0000 1

To Delete an Existing Serial Number, enter “0“ in the loop number field. The serial number will change to

“0”s.

If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to

the display.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 71 72

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128B PLUS Einstellungsanleitung Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128B PLUS