ADEMCO 4140XMPT2 Bedienungsanleitung PDF herunterladen (Seite 44)

Dlsplaylng Descriptors

Panic Keys

Trouble Conditions

‘CheckU Messages

Other Trouble

Conditions

Power Failure

The Alpha Consoles can display all programmed descriptors, which is useful to

the installer when checking entries, and can be helpful to the user when there is a

need to identify

zones. TO display descriptors, press and hold the READY key

until the built-in instructions for that key appear, then release the key. The zone

descriptors will appear one at a time, for about 2-3 seconds each.

For faster ~

viewing,

press the READY key to display the next descriptor in numerical order

and so on. When all descriptors

have been displayed, the Control will exit display

mode. To exit display mode before all descriptors

have been displayed, enter the

security code and press the OFF key.

There are three panic key pairs (shown below) that, If programmed, can be

used

to manually initiate alarms and send a report to the central station.

Each key pair

can be individually programmed for 24 Hour Silent, Audible or Auxiliary

(Emergency) responses. The panic function is activated when the appropriate

key pair is pressed at the same time.

The panic functions are identified by the system as follows:

PANIC

~] +[1]

For 5137AD consoles, these panic keys can also be

~]:;] :: programmed with an alpha descriptor.

IMPORTANT: For the Panic functions to be of practical value, the system must

be connected to a central station.

The word “CHECK” on the Console’s display, accompanied by a rapid ‘beeping”

at the Console, indicates that there is a trouble condition in the system. The

audible warning sound can be silenced by pressing any key. Instruct users to call

for service immediately upon

seeing any of the following messages.

● A display of “CHECK” accompanied by a display of one or more zone

descriptor(s) indicates that a problem exists with those zone(s). First, determine

if the zone(s) displayed are intact and make them so if they are not. If the

problem has been corrected, key an OFF sequence

(Code plus OFF) to clear

the display.

● A display of the word “CHECK” accompanied by a numeric display of “97” ~

indicates that a short exists on the Polling Loop and may eliminate some of the

protection. Fault “97” can be assigned an alpha descriptor when using the

5137AD console.

● A display of the word “CHECK accompanied by a numeric display of “88, “89”,

“90”, or “91” indicates a 4280 Receiver problem. Faults “88”, “89” “90” & “91”

can be assigned alpha descriptors when

using the 5137AD console.

● A display of “COMM. FAILURE” (5137AD) or “FC (4137AD) at the Console

indicates that a failure occurred in the telephone communication portion of your

system.

● A display of “LO BAT” (5137AD) or “BAT” (4137AD) and a zone descriptor,

accompanied

by a once per minute beep at the Console indicates that a low

battery condition exists in the wireless transmitter displayed. The audible

warning sound may be silenced by pressing any key. A display of ‘SYSTEM LO

BAT” (5137AD) or “BAT” with no zone number (4137AD) indicates that a low

battery condition exists with the system’s backup battery.

● A display of “RCVR SET UP ERROR” (5137AD) or “E8” (4137AD) at the

console indicates that the system has more RF zones programmed than the RF

receiver can support, If this is not corrected, none of the zones in the system

will be protected. If more than 8 RF zones are desired, use a Receiver that

supports

more than 8 zones (4280, 4281 H, 5881 H).

● A display of “MODEM COMM” (5137AD) or “CC” (4137AD) indicates that the

control is on-line with the remote computer and the control is not operating.

Panel’s response to alarm and trouble conditions will be delayed until on-line

session is completed.

Ifthe POWER indicator is off, and the message “AC LOSS” (5137AD) or “NO AC”

(4137AD) is displayed,

the Console is operating on battery power only. Check to

see that your system’s plug-in transformer has not been accidentally pulled out. ~

Instruct the user to call a service representative immediately if AC power cannot

be restored.

-44-

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4140XMPT2 Bedienungsanleitung Seite 44

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4140XMPT2