ADEMCO 4140XMPT2 Bedienungsanleitung PDF herunterladen (Seite 17)

WIR~LMS RXPANSION (Zones 1=63)

Oonwal Information

[Rooolvm’a)

TransmJttcrs Supported

bv varloua rocolvers

Roe.ivor

4280 6%

4281M 8

4281L 4

S881H 84

S881M

eQni

I’hefoliowlng tables

tones Supported

~FRsoeivers(Qenord

Receiver Supervision

House Identification

Sniffer Mode For

House Id

(Code + [#]+ [2])

rwnarizeswireless exBan8ion oharaoterlstios.

c The 8ystem supports up to 83 wireless transmitters

(5700 or 5800 series), plus a wireless keypad.

BTo expand the system using wireless, one or two of the

same type of RF Reoelvers can be used.

~ Any zone from 1-83 can be used as

a 5700 aerie8

wireless zone. The total number of trarwmlttere

SUPPCNW byeach reoelver Is shown In the

transmitted

supportedtable. Any

zone from 1=87 can be used asa

5800serieswirelesszone.

The 4140XMPT2 supports the 4280, 4281 and 5881

series RF reoelvere. Refer to the transmitters auppotted

ta:av:r the number of zones supported by each

The receivers respond to status and alarm signals from

wkeleee transmitters (@345MHz USA; 315MHz Canada)

within a nominai range of 200 feet, and reiay this

information to the oontroi,

Two of the same type of receivers can be used to

provide either a greater area of coverage, or to provide

redundant protection, The type of receiver used is

identified in program field 1’32,

Receivers must be mounted externally to the controi,

The 4280 & 4280-8 receivers are connected to the

poliing loop.

The 4281 and 5881 series receivers are connected to

the consoie data iines.

●

if the connection is broken between the receiver and the

controi panel, a TROUBLE wili be dispiayed for zones 89

or 91 (if type 05 is assigned). in addition, aii zones

associated with the RF device

will report a trouble

condition.

If, within a programmed intervai of time, the receiver does

not hear from any of its transmitters, a TROUBLE wiii

appear for zones 88 or 90 (if type 05 is assgned).

4280 oniy: if the cover of the 4280 is removed, a

TROUBLE wiil be dispiayed for zones 89 or 91 (if type 05

is assiqned).

● Receivers respond oniy to transmitters set to the same

house iD (01-31). This prevents system interference

from transmitters in other nearby systems.

c Use Sniffer Mode (described later) to make sure you do

not choose a House ID that is in use in a nearby system.

● 4280 house ID is set via DiP switches.

● 4281/5881 (for 5827) house iD is programmed via #93

Menu Mode, Device Programming.

●

To check for house iDs being used in nearby systems,

set the receiver’s House iD to “00”, then enter your

“Instailer Code”+ [#]+

[2]

The receiverwill now “sniff” out any House iDs in the area

and display them. Keeping the receiver in this mode for

about 2 hours wiii give a good indication of the house IDs

being used. To exit the Sniffer Mode, simpiy key your

instailer code + OFF, then set your house iD to

onenot

dispiayed in the “Sniffer Mode”.

Important: Since Sniffer Mode effectively disabies RF

point reception, Sniffer Mode cannot be entered whiie

any partition is armed.

-17-

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4140XMPT2 Bedienungsanleitung Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4140XMPT2