ADEMCO 4140XMPT2 Bedienungsanleitung PDF herunterladen (Seite 23)

VOLTAGE TRIGGERS (Connector J7)

(Ground Start Module, Keyswitch, Remote Console Sounder)

General Information

Connector J7, located on the right hand side of the main PCB provides 4 trigger

outputs for operating the 675 Ground Start Module, the 4146 Keyswitch, a

remote console sounding piezo, and for triggering auxiliary alarm signaling

equipment (such as the 7720 and 7920SE LORRA Subscriber Radios). Note that

these output triggers can be enabled by partition via programming field 2*20.

The pin assignments of this connector are shown below. Use only the 4142TR

9-wire cable (available as an option) for making connections to this connector,

output 1

J7 CUNNCCTON

outputs 2 & 4

OUT !: GROUNO START OR OPENJCLOSE

OUT 2. FIRE OR KEYSWITCH ARMED LEO

OUT 3. BURGLAtW/AUOISLE PANIc/AuxILIARY

OUT 4; SILENT PANICIOURESS OR KEYSWITCH READY LEO

Output 2,3 &4 Rating:

Ground Start Module

Not intended for use In

UL Listed anplicatlons.

Operates, by default, as a trigger for the 675 ground

start module.

This output may optionally be

programmed to operate as an operdclose trigger or as a

remote console sounder output. Only one of these

options may be used at any time.

Rating:

When Activated: 10 -13.8 VDC through 4K

ohms

(2.5MA max)

When De-activated: 100 ohms to ground

Operate, by default, as Fire and Silent Panic/Duress

triggers respectively. These triggers may optionally be

programmed to act as Arm and Ready status indicators

when it is desired to use the 4146 keyswitch.

When Activated: 10- 13.8 VDC through 5K ohms

(2MA max)

When De-activated: 1k ohms to ground

An optional 675 Ground Start module can be used for installations having

telephone lines which require ground start instead of loop start operation to

obtain dial tone from the telco central office.

If used, program field 1●46 must be set to “O” (factory default) and the 675

Ground Starl Module must be connected to the panel’s J7 connector trigger

output 1, to auxiliary power, and to the “RING” side of the telephone line as

shown in the diagram below.

Use the following procedure to determine which side of the telephone line is the

“RING side:

a. Connect the “+” lead of a DC voltmeter to earth ground, and the “-” lead to

one side of the telephone line.

b. The wire which reads +50VDC is the “RING” side,

When the panel has a message to transmit to the central station, it will seize the

line, go off hook, and then trigger the 675 module to connect the “RING” side of

the telephone line to earth ground. The panel will cause the module to break the

connection between “RING” and earth ground when a dial tone is obtained.

4147TR CALIIJ

.17 C0NNEl,70n

‘Q%+b

:0”

mTouNO START

TRIGGER

GnAY

47$

71LUE

Q+

OROuNo

STAR

YELLOW

MODU..

—–—

BLACK

“+0

TERMINAL r

(CUT QUANGE

-i+

WHITE

JUMPER)

$ $

,, . ~ TO AUXPOWER -

~40,

l+#~::~g::;ORAw‘:O:N :

To TELCO To EARTH

RING

GROUND

1) OUT 1 IS NO LONGER

USABLE FOR OPEWCLOSE

BROWN

!SEE FIELD 1, 46).

Q90

2) OUT 2,3,4 CAN STILL BE

uSED TO PROVIDE

ALARM

BLUE

STATUS INDICATIONS OR

TO OPERATE A KEYSWITCH

(SEE FIELD 15).

3) THE 675 IS NOT UL LISTED

BLACK

-23-

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 67 68

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4140XMPT2 Bedienungsanleitung Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4140XMPT2