ADEMCO Vista-50 Einstellungsanleitung Seite 22
- Seite / 112
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
VISTA-50P/VISTA-50PUL Installation and Setup Guide
3-10
-
+
-
+
-
+
EOL POWER
SUPERVISION
RELAY MODULE
A77-761B
4-WIRE SMOKE
DETECTORS
2000
OHM
EOLR
TO FIRE ZONE
TERMINALS
HEAT
DETECTOR
+
–
SHOWN POWERED.
RELAY OPENS WHEN
POWER IS LOST
333PRM-003-V0
POWER
SUPPLY
333 PRM
7
6
5
4
3
+
-2
+1
8
JUMPER
P1
USE A 12VDC,
BATTERY-BACKED,
UL LISTED POWER
SUPPLY.
JUMPER P1 ON
333 MODULE
MUST BE IN
"B" POSITION
FOUR-WIRE DETECTOR CIRCUIT
4204
CONTROL PANEL
234 112
76 4
Figure 3-14: Wiring a 333PRM using a 4204 and a Power Supply
Using 2-Wire Latching Glassbreaks on Zone 8
Zone 8 can support 2-wire glassbreak detectors. The
zone provides enough standby current to power up to 50
2-wire glassbreak detectors meeting the requirements
listed below.
Compatible Glassbreak Detectors
Use detectors that meet the following ratings:
Standby
Voltage:
5VDC–13.8VDC
Standby
Resistance:
Greater than 20k ohms (equivalent
resistance of all detectors in parallel)
Alarm
Resistance:
Less than 1.1k ohms (see note below)
Alarm
Current:
2mA–10mA
Reset Time:
Less than 6 seconds
NOTES:
• You can use detectors that exceed 1.1k ohms in
alarm, provided they maintain a voltage drop of
less than 3.8 volts in alarm.
• The ASC-SS1 detector has been tested and found to
be compatible with these ratings.
21
22
GLASSBREAK
DETECTOR
ZONE 8
(+)
(-)
LATCHING TYPE GLASS
BREAK DETECTOR LOOP
2000
OHMS
EOLR
Figure 3-15: Wiring Latching Glassbreaks to Zone 8
• The alarm current provided by zone 8
supports only one glassbreak detector in
the alarmed state.
• Do not use other N.O. or N.C. contacts
when using glassbreak detectors on zone
8. Other contacts may prevent proper
glassbreak detector operation.
To wire 2-wire latching glassbreak detectors to zone 8,
perform the following steps:
Step Action
1 Select compatible 2-wire glassbreak
detectors that meet the requirements stated
previously.
2 Connect detectors across zone 8 (terminals
21 and 22). See Figure 3-15.
3 Connect the EOL resistor at the last detector
in the loop across the zone’s terminals. You
must connect the EOL resistor across
the loop wires at the last detector.
- Table of Contents 3
- List of Figures 5
- General Description 7
- Partitioning 9
- OFFICE 1 OFFICE 2 10
- MAIN ENTRANCE 10
- COMMON LOBBY 10
- V128BP-001-V0 10
- B = Bypassed/Ready 11
- = Alarm/Trouble 11
- Installing the Control 13
- Installing the Keypads 15
- Installing External Sounders 16
- ALARM SOUNDER OUTPUT: 17
- 1-VDC - 13.8VDC 17
- 1.7A MAXIMUM 17
- Telephone Line Connections 18
- ZONE 1,8: 100 OHMS MAXIMUM 19
- Figure 3-11 20
- 333PRM-001-V0 21
- 333PRM-003-V0 22
- Installing RPM Devices 23
- GAUGE LENGTH 24
- #22 650 FT 24
- #20 950 FT 24
- #18 1500 FT 24
- #16 2400 FT 24
- Wireless Zone Expansion 25
- 5881ENHC-001-V0 26
- Device Programming 27
- Menu Mode 27
- Installing Output Devices 29
- 123456789 30
- Remote Keypad Sounder 31
- Installing a 4100SM 32
- #93 Menu Mode 33
- Figure 3-29 34
- CONTROL PANEL 35
- Connecting the Transformer 36
- Programming 41
- #93 Menu Mode Programming 42
- Zone Number Designations 44
- Section 4 – Programming 45
- Polling Loop Supervision 46
- SECTION 3 46
- Programming for 4100SM 47
- Data Field Descriptions 49
- Support 56
- Scheduling Options 65
- Time Window Definitions 66
- Windows Programming 68
- Holiday Schedule Programming 68
- Time-Driven Event Programming 69
- Limitation of 69
- Access Schedules Programming 69
- #80 Scheduling Menu Mode 69
- Daily Open/Close Schedules 70
- Holiday Schedules 70
- Time-Driven Events 71
- EXPLANATION 73
- Temporary Schedules 75
- User Scheduling Menu Mode 76
- Downloading Primer 79
- On-Line Control Functions 80
- Direct-Wire Downloading 81
- Telco Handoff 81
- Setting the Real-Time Clock 83
- User Access Codes 85
- Multiple Partition Access 86
- Exiting the User Edit Mode 88
- Testing the System 89
- Trouble Conditions 91
- To the Installer 91
- Contacting Technical Support 92
- Regulatory Agency Statements 93
- Requirements 94
- Summary of System Commands 97
- Specifications 99
- Contact ID Event Codes 101
- Index-1 103
- Index-4 106
- WARNING! 108
- LIMITED WARRANTY 109
- N5944-6V2 5/04 Rev A 112
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-50
(234 Seiten)
(56 Seiten)
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern