ADEMCO Vista-50 Einstellungsanleitung Seite 19
- Seite / 112
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
VISTA-50P/VISTA-50PUL Installation and Setup Guide
3-7
++
-
N.C.
N.C.
N.O.
2k EOLR 2k EOLR
+-
++
-
N.C.
N.C.
2k EOLR 2k EOLR
++
-
N.C.
+
+
-
N.C.
N.C.
2k EOLR
SMOKE
Zone resistance (Excluding EOLR):
ZONE 1,8: 100 OHMS MAXIMUM
ALL OTHER ZONES: 300 OHMS MAXIMUM
ZONE 1
ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 ZONE 9
2-WIRE SMOKE
DETECTOR LOOP
(Also supports NO/NC Burg contacts)
Programmable Response
(Fast/Normal) Loop
LATCHING TYPE GLASS
BREAK DETECTORS
10 11 12 13 14 15 16 17 18 19 20 21 22 23
N.C.
N.O.
N.O. N.O.
2k EOLR
N.O. N.O.
N.O.
N.C.
N.O.
2k EOLR
2k EOLR
N.C.
GLASS
BREAK
Fire
Usage
Burg.
Usage
Red Jumper
Zone response time:
ZONES 1-8: 350mSec-500mSec
ZONE 9: Programmable for
Fast: 10mSec-15mSec
Normal: 350mSec-500mSec
(default response)
hw_zones-001-V0
Figure 3-9: Wiring Connections for Zones 1-9
Using 2-Wire Smoke Detectors on Zone 1
Zone 1 can support up to 16 2-wire smoke detectors.
The alarm current on zone 1 supports only one
smoke detector in the alarmed state.
Compatible 2-Wire Smoke Detectors
DETECTOR TYPE DEVICE MODEL #
Photoelectric, direct-wire System Sensor 2400
Photoelectric w/heat sensor, direct-wire System Sensor 2400TH
Photoelectric w/B401B base System Sensor 2451
Photoelectric w/heat sensor & B401B System Sensor 2451TH
Ionization, direct-wire System Sensor 1400
Ionization w/B401B base System Sensor 1451
Photoelectric duct detect (DH400 base) System Sensor 2451
Photoelectric duct detect (DH400 base) System Sensor 2451
Ionization duct detector (DH400 base) System Sensor 1451DH
Ionization, direct-wire System Sensor 1100
Ionization w/B110LP base System Sensor 1151
Photoelectric, direct-wire System Sensor 2100
Photoelectric w/heat sensor, direct-wire System Sensor 2100T
Photoelectric w/B110LP base System Sensor 2151
U
L
These smoke detectors are UL Listed for use
with the VISTA-50P/VISTA-50PUL and are
the only 2-wire smoke detectors that may be
used.
Wiring 2-Wire Smoke Detectors to Zone 1
2K EOL resistors must be used on fire zones
and must be connected across the loop wires
of each zone at the last detector.
To wire 2-wire smoke detectors to zone 1, perform the
following steps:
Step Action
1 Select up to 16 2-wire smoke detectors from
the list of compatible detectors.
2 Connect 2-wire smoke detectors across zone 1
terminals (10 and 11) as shown in Figure 3-
10. Observe proper polarity when connecting
the detectors.
3 Connect the EOL resistor at the last detector
in the loop across the zone 1 terminals. The
EOL resistor must be connected across
the loop wires at the last detector.
2k EOLR
ZONE 1
SMOKE
(+)
(-)
2-WIRE SMOKE
DETECTOR
10
11
(+)
(-)
Figure 3-10: 2-Wire Smoke Detector on Zone 1
- Table of Contents 3
- List of Figures 5
- General Description 7
- Partitioning 9
- OFFICE 1 OFFICE 2 10
- MAIN ENTRANCE 10
- COMMON LOBBY 10
- V128BP-001-V0 10
- B = Bypassed/Ready 11
- = Alarm/Trouble 11
- Installing the Control 13
- Installing the Keypads 15
- Installing External Sounders 16
- ALARM SOUNDER OUTPUT: 17
- 1-VDC - 13.8VDC 17
- 1.7A MAXIMUM 17
- Telephone Line Connections 18
- ZONE 1,8: 100 OHMS MAXIMUM 19
- Figure 3-11 20
- 333PRM-001-V0 21
- 333PRM-003-V0 22
- Installing RPM Devices 23
- GAUGE LENGTH 24
- #22 650 FT 24
- #20 950 FT 24
- #18 1500 FT 24
- #16 2400 FT 24
- Wireless Zone Expansion 25
- 5881ENHC-001-V0 26
- Device Programming 27
- Menu Mode 27
- Installing Output Devices 29
- 123456789 30
- Remote Keypad Sounder 31
- Installing a 4100SM 32
- #93 Menu Mode 33
- Figure 3-29 34
- CONTROL PANEL 35
- Connecting the Transformer 36
- Programming 41
- #93 Menu Mode Programming 42
- Zone Number Designations 44
- Section 4 – Programming 45
- Polling Loop Supervision 46
- SECTION 3 46
- Programming for 4100SM 47
- Data Field Descriptions 49
- Support 56
- Scheduling Options 65
- Time Window Definitions 66
- Windows Programming 68
- Holiday Schedule Programming 68
- Time-Driven Event Programming 69
- Limitation of 69
- Access Schedules Programming 69
- #80 Scheduling Menu Mode 69
- Daily Open/Close Schedules 70
- Holiday Schedules 70
- Time-Driven Events 71
- EXPLANATION 73
- Temporary Schedules 75
- User Scheduling Menu Mode 76
- Downloading Primer 79
- On-Line Control Functions 80
- Direct-Wire Downloading 81
- Telco Handoff 81
- Setting the Real-Time Clock 83
- User Access Codes 85
- Multiple Partition Access 86
- Exiting the User Edit Mode 88
- Testing the System 89
- Trouble Conditions 91
- To the Installer 91
- Contacting Technical Support 92
- Regulatory Agency Statements 93
- Requirements 94
- Summary of System Commands 97
- Specifications 99
- Contact ID Event Codes 101
- Index-1 103
- Index-4 106
- WARNING! 108
- LIMITED WARRANTY 109
- N5944-6V2 5/04 Rev A 112
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-50
(234 Seiten)
(56 Seiten)
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.216 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern