ADEMCO Alpha Vista Console Bedienungsanleitung PDF herunterladen (Seite 73)

ADDENDUM TO: INSTALLATION INSTRUCTIONS FOR 5140XM CONTROL

USE WITH ISSUE: N6019V1

RE: Feature Changes and New Program Fields

This addendum applies to 5140XM Controls which are shipped with firmware EPROM

marked:

WA5140XM-XX (where XX = 18 or higher)

The EPROM is located beneath the main PC board shield cover.

The following features are new for the 5140XM Control.

1. In accordance with revisions to UL864, Standard for Commercial Fire Alarms, the following

system changes have been made.

Silencing Console Sounds for Fire Supervisory Zone Type now requires security code + OFF

To silence console sounds triggered by supervisory conditions on zones programmed for fire zone

supervisory response (zone response type 18), you must enter the security code + OFF. Prior to this

change, these console sounds could be silenced by pressing any key (no security code was needed).

Keyswitch Mode 2 Operation (field *15)

New fire or burglary alarm conditions occurring after a previous alarm was silenced using the

keyswitch will now automatically re-activate the corresponding fire or burglary alarm bell circuits when

keyswitch mode 2 operation is selected (field *15 set to 2). Prior to this change, alarm bell circuits

remained silenced until the security code + OFF was entered at a console.

Note that when keyswitch mode 2 operation is selected, operating the keyswitch will silence fire and

burglary alarms only when a fire alarm condition is present (in accordance with the existing

Installation Instructions).

OFF-NORMAL Communicator Test Report (new program fields 3*53, 3*54)

Off-normal conditions are fire alarm system related conditions existing at the time a normal test report

is sent. These conditions include fire alarms, fire troubles or supervisories, and certain system

troubles such as earth ground faults, AC failure, low system battery, or bell circuit faults. The 5140XM

now transmits an "off-normal" communicator test report (programmed in field 3*53, 3*54) instead of

the normal communicator test report (programmed in fields *81, *82) when fire alarm system off-

normal conditions are present at the time of test report transmission.

As shipped, both reports are disabled and must be enabled for installations that provide fire alarm

central station service. The normal communicator test report is enabled as described in the

Installation Instructions. The off-normal communicator test report is enabled as follows:

Field 3*53 Field 3*54

First Digit Second Digit

| |

For Ademco High Speed and Ademco Contact ID report formats: Enter "01" in field 3*53.

Ademco High Speed off-normal test reports use channel 3 =1 and status channel = 9

Contact ID sends code 608.

For Low Speed Formats: Enter the first (event code) digit of the report in field 3*53 and the second

(zone number) digit of the report in field 3*54. These fields require that two numbers be entered for

each digit of the report (i.e. enter 00 if no digit is to be sent, enter 01 for "1", enter 10 for "A"..., enter

15 for "F").

Note: fields 3*53 and 3*54 can also be programmed by loading one of the four built-in communication

defaults as follows:

Communicator Default 3*53 Value 3*54 Value

Low Speed (*94*80) 05 00

Ademco Express (*94*81) 15 00

Ademco High Speed (*94*82) 01 00

Ademco Contact ID (*94*83) 01 00

1 2 ... 68 69 70 71 72 73 74

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Alpha Vista Console Bedienungsanleitung Seite 73

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Alpha Vista Console