ADEMCO Alpha Vista Console Bedienungsanleitung PDF herunterladen (Seite 45)

V1l. PROGRAMMING THE SYSTEM

GENEWL PROGRAMMING PROCEDURES

GENERAL INFORMATION

lISER-FRIENDLY ZONE.

IDEVICE & ALPHA

PROGRAMMING (#93

Menu Mode)

,-.

COMMUNICATION

DEFAULT

PROGRAMMING

F)RoG]~MMING STEPS

The system is shipped with a set of pre-programmed values that are designed to

meet the needs of many installations. These can be changed by the installer to

suit specific needs if desired, In addition, four sets of pre-programmed

communication default values can also be loaded by the installer, each set

designed for a specific communication format. These too can be changed to suit

the needs of a patiicular installation.

Changes to these pre-programmed values can be programmed directly from the

console or from an IBM compatible computer terminal either remotely (using a

HAYES 1200 SMARTMODEM) or at the job site (using the 41OOSM Serial

Module). NOTE: Remote downloading is not a UL Listed feature. Both methods

use the 4130PC Downloading software (be sure that the software version used

includes a 5140XM menu selection). See the DOWNLOADING section for more

information.

For alpha consoles, Engfish Language descriptions of the zones and a custom

installer message (which appears when the system is ready to arm) can be

programmed using the built-in vocabulary of words (see #93 MENU MODE,

ALPHA PROGRAMMING paragraphs later in this section),

To help set up the syetem quickly and accurately, Ademco has provided a

tremendous aid to the programming process. Instead of the traditional method of

programming all the fields associated with zones, you may now logi~lly program a

zone for all its characteristics as prompted by fhe 5140XM (refer to the W3 MENU

MODE, ZONE PROGRAMMING section for details). This ensures that a zone

response type has been assigned to each zone.

This user-friendly scheme for programming eliminates the possibility of you

forgetting to enter a field properly or simply forgetting it altogether! The system

can now be programmed the way you approach your installations, by zones!

Ttis User Friendly Menu Mode can also be used for programming remte console

characteristics, and for entering alpha descriptors.

There are five sets of pre-programmed defaults available (one standard, plus four

different communication defaults). Any one of these can be loaded into the

system’s memory. Refer to the COMMUNICATION PROGRAMMING section for

instructions.

Enter Programming mode

Programming mode can be entered in one of two ways.

1) By depressing fhe ~] and [#] keys at the same time within 30 seconds

after power is applied to the Control.

2) By keying the installer code, followed by depression of CODE + O + O

keys. The facto~ installer code can be changed once in the program

mode.

Immediately following entry into the program mode, the following will be

displayed: Program Mode

● Rll # Mew . Oo

Following the above display, the system is ready to be programmed for the

communication fomat parameters, or accept data entries.

Set Standard and/or Communication Defaults

Refer to the PROGRAMMING COMMUNICATION DEFAULTS section for

further instmct;ons if one of the four communication default programming

sets is used.

Program data fields for system parameter

Program all system programming fields, including phone numbers and

account numbers, as well as any other programming fields required to

customize the system to the needs of the installation. Refer to the

PROGRAMMING DATA FIELDS section for specific commands and

instructions.

Use #93 Menu Mode for zone programming

Refer to the ZONE PROGRAMMING

section to program zone response

types.

—45—

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 73 74

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Alpha Vista Console Bedienungsanleitung Seite 45

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Alpha Vista Console