ADEMCO VISTA-100 Bedienungsanleitung Seite 88
- Seite / 234
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
16-1
SECTION 16
Event Log Options
••••••••••••••••••••••••••••••••••••••••••••••••
In This Section
♦
General Information
♦
Event Log Printer Connections
♦
Programming Event Log Options
♦
Event Logging Procedures
••••••••••••••••••••••••••••••••••••••••••••••••
General Information
The VISTA-100 has the ability to record up to 224 events of various types in a history log.
Each event is recorded in one of six categories with the time and date of its occurrence (if
the real-time clock is set). These categories are:
•Alarm
• Supervisory/check
•Bypass
• Open/close
• System conditions
• Test
The log can be viewed (Display Mode) on an alpha keypad, or printed (Print Mode) on a
serial printer connected to the system via a 4100SM Serial Interface Module.
Event Log Printer Connections
The VISTA-100's event log can be printed on a local serial printer. If the event log is used,
program field 3*19 must be set to 1.
The event log setting overrides the functions for INPUT 1 and OUT 2 that you programmed in field
3*20.
To enable event log printing, take the following steps:
Connect a UL EDP Listed serial printer to the J2 connector using an ADEMCO 4100SM
Interface module, as shown in Figure 16-1.
Configure the printer according to the following requirements:
• 8 data bits, no parity, 1 stop bit
• 300 or 1200 baud (1200 preferred)
• Hardware handshaking using DTR signal
- VISTA-100 1
- Table of Contents 4
- List of Figures 9
- How To Use This Manual 10
- 00 INSTALLER CODE 11
- General Description 12
- Section 8: 13
- Wireless Expansion 13
- Planning a Partitioned System 18
- Common Lobby Logic 19
- COMMON LOBBY 20
- In This Section 24
- Recent Close Report 25
- Exit Delay Reset 25
- Cross Zoning 25
- Call Waiting Defeat Logic 26
- Installing The Control 28
- Installing The Keypads 32
- Figure 5-2 33
- Mounting the Keypads 34
- Programming Remote Keypads 35
- Basic Hardwired Zones 001-008 36
- 2-WIRE SMOKE 37
- DETECTOR 37
- Figure 6.2 38
- Zone 6 Tamper Configuration 39
- 2-Wire Polling Loop Expansion 42
- (Zones 9 - 87) 42
- Wire Gauge Max. Length 43
- #22 gauge 650 feet 43
- #20 gauge 950 feet 43
- #18 gauge 1500 feet 43
- #16 gauge 2400 feet 43
- Section 17: 44
- Power-Up Procedure 44
- Polling Loop Supervision 46
- Wireless Zone Expansion 48
- 1 2 3 4 5 50
- Programming the RF Receiver 51
- House ID Sniffer Mode 51
- 5700 Series Transmitter Setup 52
- 5800 Series Transmitter Setup 54
- Relay Outputs 58
- 121110987654321 59
- 4285/4286 VIP Module 62
- Wiring the VIP Module 63
- Programming the VIP Module 64
- Section 18: 67
- The Mechanics of 67
- Programming 67
- J2 Trigger Outputs 70
- 5140LED Indicator Module 73
- 7720 WIRING DIAGRAM 75
- BURGLARY/AUDIBLE 76
- PANIC ALARM 76
- Event Log Printer Connections 77
- Direct Wire Downloading 77
- External Sounders 79
- Programming the Bell Outputs 80
- (Model 610-7) 81
- Auxiliary Relay 82
- Four-Wire Detector Circuit 83
- Section 14- Auxiliary Relay 84
- Dialer Outputs 85
- Dialer Operation 86
- Section 15- Dialer Outputs 87
- Event Log Options 88
- Programming Event Log Options 89
- Event Logging Procedures 90
- Section 16- Event Log Options 92
- Final Power-Up Procedure 93
- Backup Power Calculations 94
- Cannot exceed 128MA 95
- BATTERY SELECTION TABLE 98
- Section 17 – Final Power-Up 99
- The Mechanics Of Programming 100
- Viewing Data Fields 101
- Entry Errors 101
- #93 Menu Mode Programming 103
- Zone Type Definitions 104
- Zone Index/Zone Type Defaults 108
- Zone Type Defaults 109
- Data Field Descriptions 110
- 995 996 999 112
- Prm. Sec 115
- 95 96 99 Duress 116
- [15 15 15 15] 117
- Alm Chck Byps O/C Systm Test 120
- Bell 1 Bell 2 123
- Main Backup 124
- 16 17 18 124
- Bell 2 Aux 124
- Bell 2 Aux. Rly 125
- Zone Programming 128
- 010 LEARN S/N? 131
- 1 = YES, 0 = NO 1 131
- 010 INPUT S/N 131
- Axxx-xxxx 131
- Zone Number Entered 133
- Report Code Programming 135
- Programming Alpha Descriptors 138
- ****DISARMED**** 141
- READY TO ARM 141
- ****DISARMED**** 141
- (For Adding Custom Words) 143
- Device Programming 144
- Relay Programming 145
- Zone List Programming 149
- Relay Voice Descriptors 150
- CUSTOM INDEX? 151
- 0=no 1=yes 151
- CUSTOM WORD NO 151
- RF Serial Number Clear Mode 152
- Scheduling Options 153
- Time Windows Definitions 155
- Open/Close Definitions 157
- Programming Time Windows 160
- Daily Open/Close Worksheet 161
- Programming Holiday Schedules 163
- Time-Driven Event Worksheet 164
- Time-Driven Event Programming 166
- Access Control Schedules 168
- #83 User Scheduling Menu Mode 172
- System Communication 174
- Downloading Primer 184
- On-Line Control Functions 185
- Access Security 186
- J2 CONNECTOR 187
- Setting The Real-Time Clock 188
- User Access Codes 190
- User 3 User 3 193
- Level 1 Level 4 193
- Master Oper B 193
- To EXIT the User Edit Mode 195
- Keypad Functions 196
- Global Arming 197
- Closing Delay? 198
- Hit 0-2 Hours 198
- Viewing Zone Descriptors 199
- Viewing Downloaded Messages 199
- Panic Keys 199
- Speed Key “D” (Macros) 199
- ENTER SPEED KEY 200
- "D" 200
- ENTER DEVICE NO 200
- 00=QUIT 01 200
- HIT 0=OFF , 1=ON 201
- HIT THE "*" KEY 201
- Testing The System 202
- DISARMED 203
- DISARMED Press 203
- Battery Test 205
- Dialer Test 205
- Armed Burglary System Test 207
- Trouble Conditions 208
- To the Installer 209
- Regulatory Agency Statements 212
- Appendix A-4 215
- Appendix A-5 216
- Appendix A-6 217
- DIP Switch Tables 218
- Appendix B-3 220
- Appendix B-4 221
- Summary of System Commands 222
- Specifications 224
- DIGITAL COMMUNICATOR 225
- 6139(R) REMOTE KEYPAD 225
- WARNING! 230
- Appendix-6 231
- SUMMARY OF CONNECTIONS 233
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO VISTA-100
(8 Seiten)
(56 Seiten)
(16 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.240 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern