ADEMCO Vista-128B PLUS Spezifikationen PDF herunterladen (Seite 57)

Section 4 – Programming

4-7

Type 07: 24-Hour Audible Alarm

Sends a report to the central station and provides an

alarm sound at the keypad and an audible external

alarm. Assign this zone type to a zone containing an

Emergency button.

Type 08: 24-Hour Auxiliary Alarm

Sends a report to central station and provides an alarm

sound at the keypad only.

(No bell output is

provided.)

Assign this zone type to a zone an

Emergency button or one containing monitoring devices

such as water sensors or temperature sensors.

Type 09: Supervised Fire (Without Verification)

Provides a fire alarm on a short circuit and a trouble

condition on open circuit. A fire alarm produces a

pulsing of the bell output. A zone of this type is always

active and cannot be bypassed.

Type 10: Interior with Delay

Provides entry and exit delays (using the programmed

entry and exit delay times) when armed in the AWAY

mode. Provides only exit delay when armed in the

MAXIMUM mode (no entry delay).

If the Interior with Delay zone is programmed for one

of the STAY modes (default is STAY mode 1), it is

automatically bypassed when the panel is armed in the

STAY or INSTANT mode. Delay begins whenever

sensors in this zone are violated, regardless of whether

or not an entry/exit delay zone was tripped first.

Assign this zone type to a zone covering an area such as

a foyer, lobby, or hallway through which one must pass

upon entry or exit (to and from the keypad).

Type 14: PLM Supervision

Provides supervision of remote Panel Link Modules. If

the communication between the local PLM and a

remote PLM fails, a trouble message is produced for the

PLM zone.

Type 16: Fire With Verification

Provides a fire alarm on a short circuit and a trouble

condition on open circuit. An initial short detection

causes 7-second smoke detector power reset. A

subsequent short detection within 90 seconds of the

reset causes a fire alarm. A fire alarm produces a

pulsing of the bell output. A zone of this type is always

active and cannot be bypassed.

Type 20: Arm-STAY (5800 Series devices only)

Causes the system to arm in the STAY mode when the

zone is activated.

Type 21: Arm-AWAY (5800 Series devices only)

Causes the system to arm in the AWAY mode when the

zone is activated.

Type 22: Disarm (5800 Series devices only)

Causes the system to disarm when the zone is

activated.

Type 23: No Alarm Response

Used on a zone when an output relay action is desired,

but with no accompanying alarm (e.g., for lobby door

access).

Type 27: Access Point

Assign this zone type to an input device (hardwired

zone, wireless zone, keypad, access control relay, etc.)

that controls an access entry point (e.g., a door). The

access point entry relay can be assigned to an access

control relay (controlled by the VISTA-128BP/VISTA-

250BP), ECP relay (4204), or to the access control

system independent of the control panel.

Type 28: Main Logic Board (MLB) Supervision

Used to supervise the MLB. If communication between

the MLB and the VISTA Gateway Module (VGM) fails,

a trouble condition is annunciated for the zone. Also, if

the communication fails, all access control system

(ACS) input zones also display a “CHECK.”

Type 29: Momentary Exit

Used to cause an access point programmed for entry to

revert to an exit point for 15 seconds. After the 15

seconds, it automatically reverts back to an entry point.

This zone type should be used only with VistaKey

modules.

NOTE FOR PANIC KEYS:

Keypad panic zones share the same

zone response type for all 8 partitions, but panics may be

individually enabled for each partition.

IMPORTANT! FAULT ANNUNCIATION

Polling loop and RF troubles (zones 988, 990, and 997) report as

trouble conditions only, and as such, should be assigned zone

type 05 if annunciation is desired. See

Polling Loop Supervision

and

RF System Operation and Supervision

SECTION 3

Installing the Control

for more information.

Zone Input Type Definitions

Each zone must be assigned an input type, which

defines the where the system will “look” for status of

the zone (RF receiver, polling loop, etc.). Zone input

types are defined below.

Type 01 Hardwired (HW)

Reserved for the built-in hardwired zones 1-9.

Type 02 RF Motion (RM)

Select for 5800 Series RF transmitters. Sends periodic

check-in signals, as well as fault and low-battery

signals. The control panel automatically restores the

zone to “ready” after a few seconds. This type is

designed for facilities with multiple motion detectors

that may fault and restore simultaneously. The

transmitter must remain within the receiver’s range.

NOTE:

If using RF Motion with a door/window type

transmitter, only loop 1 may be used.

1 2 ... 52 53 54 55 56 57 58 59 60 61 62 ... 127 128

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128B PLUS Spezifikationen Seite 57

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128B PLUS