ADEMCO Vista-128B PLUS Spezifikationen PDF herunterladen (Seite 24)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

3-6

Wiring Burglary and Panic Devices to Zones 1-9

The maximum zone resistance is 100 ohms for

zones 1 and 8, and 300 ohms for all other

zones (excluding the 2K EOL resistor).

To wire burglary and panic devices to zones 1-9,

connect sensors/contacts to the hardwire zone terminals

(10 through 23). See

Figure 3-9

. Connect N.C. and N.O.

devices as follows:

•

Connect N.C. devices

in series

with the high (+)

side of the loop. The 2K EOL resistor must be

connected in series with the devices, following the

last device.

•

Connect N.O. devices

in parallel (across)

the

loop. The 2K EOL resistor must be connected

across the loop wires at the last device.

N.C.

N.O.

2k EOLR 2k EOLR

N.C.

2k EOLR 2k EOLR

N.C.

2k EOLR

SMOKE

Zone resistance (Excluding EOLR):

ZONE 1,8: 100 OHMS MAXIMUM

ALL OTHER ZONES: 300 OHMS MAXIMUM

ZONE 1

ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 ZONE 9

2-WIRE SMOKE

DETECTOR LOOP

(Also supports NO/NC Burg contacts)

LATCHING TYPE GLASS

BREAK DETECTORS

10 11 12 13 14 15 16 17 18 19 20 21 22 23

N.C.

N.O.

N.O. N.O.

2k EOLR

N.O. N.O.

N.O.

N.C.

N.O.

2k EOLR

N.C.

GLASS

BREAK

Fire

Usage

Burg.

Usage

Red Jumper

Zone response time:

ZONES 1-9: 350mSec-500mSec

ZONE 9: Also Programmable

for RS232 input

HWZones-002

Figure 3-9: Wiring Connections for Zones 1-9

Using 2-Wire Smoke Detectors on Zone 1

Zone 1 can support up to 16 2-wire smoke detectors.

The alarm current on zone 1 supports only one

smoke detector in the alarmed state.

Compatible 2-Wire Smoke Detectors

DETECTOR TYPE DEVICE MODEL #

Photoelectric, direct-wire System Sensor 2400

Photoelectric w/heat sensor, direct-wire System Sensor 2400TH

Photoelectric w/B401B base System Sensor 2451

Photoelectric w/heat sensor & B401B System Sensor 2451TH

Ionization, direct-wire System Sensor 1400

Ionization w/B401B base System Sensor 1451

Photoelectric duct detect (DH400 base) System Sensor 2451

Ionization duct detector (DH400 base) System Sensor 1451DH

Ionization, direct-wire System Sensor 1100

Ionization w/B110LP base System Sensor 1151

Photoelectric, direct-wire System Sensor 2100

Photoelectric w/heat sensor, direct-wire System Sensor 2100T

Photoelectric w/B110LP base System Sensor 2151

These smoke detectors are UL Listed for use

with the VISTA-128BP/VISTA-250BP and are

the

only

2-wire smoke detectors that may be

used.

Wiring 2-Wire Smoke Detectors to Zone 1

2K EOL resistors must be used on fire zones

and must be connected across the loop wires

of each zone at the last detector.

To wire 2-wire smoke detectors to zone 1, perform the

following steps:

Step Action

1 Select up to 16 2-wire smoke detectors from

the list of compatible detectors.

2 Connect 2-wire smoke detectors across zone 1

terminals (10 and 11) as shown in

Figure 3-

. Observe proper polarity when connecting

the detectors.

3 Connect the EOL resistor at the last detector

in the loop across the zone 1 terminals.

The

EOL resistor must be connected across

the loop wires at the last detector.

2k EOLR

ZONE 1

SMOKE

(+)

(-)

2-WIRE SMOKE

DETECTOR

(+)

(-)

Figure 3-10: 2-Wire Smoke Detector on Zone 1

Using 4-Wire Smoke Detectors on Zones 1-8

You may use as many 4-wire smoke detectors as can be

powered from the panel's Auxiliary Power output

without exceeding the output's rating (750mA).

Auxiliary power to 4-wire smoke detectors is

not automatically reset after an alarm, and

therefore must be momentarily interrupted

using either the J7 smoke detector reset output

trigger or a 4204 Relay Module.

Compatible 4-Wire Smoke Detectors

Use any UL Listed 4-wire smoke detector that is rated

for 10-14VDC operation and that has alarm reset time

not exceeding 6 seconds. Some compatible 4-wire

smoke detectors are listed below.

Detector Type Detector Model #

Photoelectric, direct wire System Sensor 2412

Photoelectric w/heat

sensor, direct wire

System Sensor 2412TH

Ionization, direct wire System Sensor 1412

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 127 128

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128B PLUS Spezifikationen Seite 24

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128B PLUS