ADEMCO Vista-128B PLUS Spezifikationen PDF herunterladen (Seite 42)

VISTA-128BP/VISTA-250BP Installation and Setup Guide

3-24

Using the 4100SM

To connect a serial printer using the 4100SM, refer to

Figure 3-33

and perform the following steps:

Step

Action

Connect terminal 23 on the control panel to

terminal 3 on the 4100SM.

Connect terminal 6 on the 4100SM to the

Brown wire on the 4142TR cable.

Connect the 4142TR cable to J8 on the

control.

Connect terminals 8 and 7 of the 4100SM to

terminals 6 and 7 (aux. power (+) and (-)),

respectively of the control.

Connect the UL EDP Listed serial printer to

the 4100SM Interface Module.

The 4100SM Module is supplied with a 10-

foot RS232 cable. A longer cable can be used

if the VISTA-128BP/VISTA-250BP is

separated from the serial printer by more

than 10 feet, but the total cable length should

be less than 50 feet.

123456789

J8 CONNECTOR

VIOLET

GREY

YELLOW

RED

GREEN

BROWN

BLUE

BLACK

IN 2

IN 3

GROUND

OUT 5

OUT 6

GROUND

PRINTER DTR

4142TR CABLE (SUPPLIED WITH 4100SM)

4100SM SERIAL MODULE

+ PWR

- (GND)

RXD

not used

TXD

not used

DTR

BLUE WHITE

To TB6 Aux. Power (+)

(25mA current draw)

To TB7 Aux. Power (-)

USE GENDER CHANGER

SUPPLIED WITH 4100SM

IF PRINTER HAS DB25

MALE CONNECTOR

Cable

Supplied with

4100SM

SERIAL PRINTER

SET FOR: 8 DATA BITS

EVEN PARITY

STOP BIT

300/1200 BAUD

4100SM JUMPERS

(CUT TO SET RESPECTIVE SIGNAL FLOATING)

COLOR FUNCTION PIN #

RED

BLUE

WHITE

CTS

DSR

RED

4100SM-011-V0

Figure 3-33: Printer Connections to the 4100SM

NOTE:

See the 4100SM Installation Instructions for

details concerning the serial printer operation.

Installing the 4285/4286 VIP Module

The 4285/4286 VIP Module is an add-on accessory that

permits the user to access the security system (and

relays) via a TouchTone telephone. This may be done

either from the premises or by calling the premises

from a remote location. Only one VIP Module can be

used in a security system. This module must be

enabled as Device Address 4 in the

Device

Programming

#93 Menu Mode

, and must be assigned

to a partition.

The 4285/4286 VIP Module is not permitted in

UL installations.

Detailed operating instructions for phone access

to the security system are provided with the VIP

Module.

The 4285/4286 VIP Module features:

•

Allows the user to receive synthesized voice

messages over the phone regarding the status of

the security system.

•

Allows the user to arm and disarm the security

system and perform most other commands using

the telephone keypad.

•

Allows the user to control relays using the

telephone keypad.

•

Provides voice annunciation over the phone to

confirm any command that is entered.

•

Announces many of the same words that would

normally be displayed on an alpha keypad under

the same system conditions. Refer to the words in

bold on the Alpha Vocabulary list found in the

#93

Menu Mode

in the

Programming Guide

•

Can be supervised for connection to control panel

(annunciated and reported as Zone 804).

The 4285/4286 is wired between the control panel and

the premises’ handset(s) (see

Figure 3-36

). It listens for

TouchTones on the phone line and reports them to the

control panel. During on-premises phone access, it

powers the premises phones. During off-premises phone

access, it seizes the line from the premises phones and

any answering machines.

•

The VIP module will not operate until the

device address (04) is enabled in the control’s

Device Programming

#93 Menu Mode

•

Do not mount the VIP Module on the cabinet

door or attempt to attach it to the PC board.

To install the VIP module, perform the following steps:

Step Action

1 Mount the module in the control cabinet if

space is available or, if this is not possible, on

the side of the cabinet or adjacent to it.

If you mount the VIP Module inside the

control cabinet,

attach it to the cabinet’s

interior surface with 2-faced adhesive tape.

You may leave the module’s cover off if it is

mounted within the cabinet.

If you mount the module outside the

cabinet,

use the screw holes at the rear to

mount horizontally or vertically (2-faced

adhesive tape may be used, if preferred).

2 Affix the 4285/4286 connections

label

(supplied separately) to the inside of the VIP

Module’s cover, if the cover is used.

Otherwise, affix the label to the inside of the

control cabinet’s

door.

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 127 128

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO Vista-128B PLUS Spezifikationen Seite 42

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO Vista-128B PLUS