ADEMCO VISTA-15PSIA Spezifikationen PDF herunterladen (Seite 8)

– 8 –

∗

∗∗

∗49

Split/Dual Reporting

0 = Standard/backup reporting only (all

to primary)

1-5 = see table at right

[0]

Backup Reporting: All reports are sent only to the primary number

unless unsuccessful after 8 attempts. If unsuccessful, the system will

make up to 8 attempts to send all reports to the secondary number. If

still unsuccessful after the 16 attempts, the system displays the

“COMM. FAILURE” message (FC for fixed-word displays).

Primary Phone No. 2nd Phone No.

1 = Alarms, Restore, Cancel Others

2 = All except Open/Close, Test Open/Close, Test

3 = Alarms, Restore, Cancel All

4 = All except Open/Close, Test All

5 = All All

∗

∗∗

∗50

Burglary Dialer Delay

Delay Time:

0 = no delay

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

V20PSIA/V15PSIA:

Delay Time:

1 = 15 seconds

2 = 30 seconds

3 = 45 seconds

Delay Disable:

0 = use delay set in entry 1

1 = dial delay disabled for zones

listed in zone list 6 (use zone list 6

to enter those zones that require

dial delay to be disabled; these

zones ignore the setting in entry 1)

UL: Dial delay plus entry delay must not exceed

one minute; use zone list 6 to disable dial delay

from appropriate zones, if necessary.

[2,0]

Delay V20PSIA/V15PSIA

Time Delay Disable

Provides delay of “BURGLARY ALARM” report to the central station,

which allows time for the subscriber to avoid a false alarm transmission.

This delay does not apply to zone type 24 alarms (silent burglary) or to

24-hour zone types 6, 7, and 8 (silent panic, audible alarm, auxiliary

alarm), which are always sent as soon as they occur.

UL: Delay Time must be 0

SIA Guidelines: delay must be minimum of 15 seconds

∗

∗∗

∗53

SESCOA/Radionics Select

0 = Radionics (0-9, B-F)

1 = SESCOA (0-9 only reporting)

Enter 0 for all non-SESCOA formats.

∗

∗∗

∗54

Dynamic Signaling Delay

0 = no delay (both signals sent)

1 = 15 secs

2 = 30 secs, etc.

UL: If using line security, must be 0.

Reports will be sent to both the dialer and

the communication device.

[0]

Select delay from 0 to 225 secs, in 15-sec increments.

Intended for reporting via a communication device on the ECP bus

(LRR). This field lets you select the time the panel should wait for

acknowledgment from the first reporting destination (see ∗55) before it

attempts to send a message to the second destination. Delays can be

selected from 0 to 225 seconds, in 15-second increments. This delay is

per message. If 0 is entered in this field, the control panel will send

redundant reports to both Primary Dialer and communication device.

∗

∗∗

∗55

Dynamic Signaling Priority /

AAV Path Select

0 = Primary Dialer first / AAV via phone

line

1 = Communication Device (LRR) first /

AAV via communication device

path (see AAV Path Select

paragraph at right)

For UL Commercial Burglary installations

that use a DACT and LRR, this field must

be 0.

[0]

This field selects the primary communication path for reporting (dialer

or communication device) of primary phone number events

†

(see ∗49

Split/Dual Reporting) and selects the communication path used for

AAV sessions (phone line or communication device path). Use ∗29

IP/GSM menu mode to enable the communication device being used.

† Dynamic signaling applies only to the primary phone number. Reports

intended for the secondary phone number are not sent via the

communication device.

For Dynamic Signaling Priority:

Select the initial reporting destination

for messages as follows:

Primary Dialer First selected (0):

• If acknowledged before delay expires (see ∗54), then message will

not be sent via LRR.

• If not acknowledged before delay expires, message is sent to both

the Primary Phone No. and via LRR.

Communication Device (LRR) First selected (1):

• If acknowledged before delay expires, then message will not be sent

to the primary dialer.

• If not acknowledged before delay expires, message is sent to both

the Primary Phone No. and via LRR.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO VISTA-15PSIA Spezifikationen Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO VISTA-15PSIA