ADEMCO VISTA-15PSIA Spezifikationen PDF herunterladen (Seite 26)

– 26 –

XX OUTPUT TYPE

DELETE 0

Output Type

0 = delete

1 = relay on 4204/4229

2 = Powerline Carrier Device

[∗] to continue

Select whether this is a relay or a Powerline Carrier (X-10)

device.

If Powerline Carrier Device (X-10) is selected, go to “A” prompt.

If relay is selected, skip to “B” prompt.

“A”

XX UNIT No.

Unit Number

01-16 = predefined address

[∗] to continue

(prompt appears if X-10 is selected)

Enter the unit code (set at the device) and press [∗].

The system returns to the Output Number prompt.

“B”

XX MODULE ADDR

07-15 yy

Module Address

07-15 = predefined address

[∗] to continue

REMOTE SERVICES NOTE: If

using the communication device’s

Multi-Mode 4204 or 2-4204

options, select one of the 4204

addresses, though a physical

4204 module is not installed. If

using 2-4204 multi-mode option,

the second 4204 address is

automatically one number higher

than the first address. Make sure

these addresses are not used by

physical 4204 modules that may

be installed. If using Multi-Mode

Enhanced Reports option, RIS

must be enabled in field *91;

when enabled, address 25 is

automatically assigned. See the

communication device’s

instructions to enable Multi-Mode.

(prompt appears if relay is selected)

Enter the predefined address for this module as listed below.

Make sure the module’s DIP switches are set to the selected

address.

Module Addresses

Address Module

07 1st 4229 (with zones 09-16)

08 2nd 4229 (with zones 17-24)

†

3rd 4229 (with zones 25-32)

†

4th 4229 (with zones 33-40)

†

5th 4229 (with zones 41-48)

12 1st 4204

13 2nd 4204

†

3rd 4204

†

4th 4204

† These addresses apply to VISTA-20P only.

XX REL POSITION

1-4 zz

Relay Position

1-4 = relay position

[∗] to continue

This is the actual (or physical) relay number with respect to the

Relay Module upon which it is located. For 4204 modules, relay

numbers are 1-4. For 4229 modules, relay numbers are 1-2.

The system returns to the Output Number prompt for

programming the next device.

REMOTE SERVICES NOTE: If using the communication device’s

multi-mode, program virtual 4204 relays to trigger on those

system events intended to be sent to the user’s email address.

(4204 option = up to 4 events; 2-4204 option = up to 8 events)

∗

∗∗

∗80 OUTPUT FUNCTION MENU MODE

(press

∗

∗∗

∗

80 while in Programming mode) The Output Definition Worksheet is on page 46.

Use this mode to program output function definitions (up to 48 functions) that provide automated control of any of the output

devices, based on events occurring on individual zones or zones with certain zone types.

Each output definition is identified

by an output function number, and includes the following components:

Output Definition Components

Component Description

Output Function No. A reference number that defines an output’s characteristics.

Activated By Determines whether the initiating event occurs on a zone, a zone list, or a zone type.

Event Event that triggers the output action. Can be an event occurring on a specific zone number or a zone list, or a

specific zone type.

Partition If the output is activated by zone type, this defines the partition in which the programmed event is to cause the

device action.

Output Action Defines the action of the relay/X-10 device when the defined event occurs. Can close for 2 seconds, stay

closed until reset, continuously pulse (1-second close-open-close-open, etc.), toggle the device state, or

activate for a defined duration (set in data field *177).

Output No. Assigns this function to a specific output number (defined in *79 Menu Mode). This is the output number that will

perform this function upon the triggering event. Note that each defined function is associated with only one

output number. This means that if more than one output device needs to perform this particular function, you

need to define another output function number with the same attributes, but assign the appropriate output

number. (i.e. output devices can be assigned more than one function number, but each function number can

only be assigned a single output number.

For example, if you want to pulse a strobe light upon fire alarms on zone 4 using a relay mapped to output number 2 (as

programmed in *79 Menu Mode), program the following in *80 Menu Mode:

Prompt Entry

Output Funct. # = 01 (assuming this is the first output function)

Activated By: = 3 (zone number)

Enter Zn No. = 04 (requires 2-digit zone numbers)

Output Action = 3 (continuous pulse)

Output Number = 02 (device mapped in *79 Menu Mode)

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO VISTA-15PSIA Spezifikationen Seite 26

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO VISTA-15PSIA