ADEMCO 5130XM Bedienerhandbuch PDF herunterladen (Seite 18)

VIII. TESTING THE SYSTEM

USING TEST MODE

After the installation is completed, the Security

System should be thoroughly tested as follows:

With the System in the disarmed state, check

that all zones are intact. If DISARMED - Press ~]

to show faults (5137) or NOT READY (4137) is

displayed, press the ~] key to display the

descriptors of the faulted zone(s). Restore faulted

ZOne(S) if necessary, 60 that “S* DISARMED***

READY TO ARM (5137) or READY (4137) is

displayed.

2. Enter the security code and press the TEST

key. The external sounder (if used) should 6ound for

3 seconds and then turn off (the system is

operating on the back-up battery only at this time).

NOTE 1. The system will not enter the Test mode if

the battery voltage is too

low, if the battery is not

connected, or if any communication messages are

waiting to be transmitted.

NOTE 2. As a reminder that the system is in the

Test mode, the Console will sound a single beep at

15-second intervals if no protection zones are

violated.

NOTE 3. In the Test mode, no alarm reports

will be

sent to the central station. Also, the external

sounder (if

used) will not be activated.

Doore ●nd windows

Open and close each protected door and window in

turn. Each action should produce three beepa from

the Console. The descriptor for each protection

zone will appear on the Console di6play.

Motion detectors

Walk in front of any interior motion detectors.

Listen for three beeps when the detector senses

movement. While it is activated, its descriptor will

remain displayed on the Console.

Note tha~

wireless PIRs will have a 3 minute lockout between

transmissions to conserve battery life.

Smoke detectors

Follow the test procedure provided by the

manufacturer of each smoke detector to ensure that

all detectors are operational and are functioning

properly.

NOTE: A 2-wire smoke detector display will not

clear until the Test mode is exited.

Turning off TEST mode

Enter the security code and press the OFF key.

ARMED SYSTEM TEST

IMPORTANT! A message will be sent to the

central station during the following tests. Notify

the central station that a test will be in progress.

NOTE: A display of “COMM. FAILURP (Alpha

consoles) or “Fe (Fixed-Word consoies) indicates a

failure to communicate (no Kissoff by the receiver

a! the central s~tion after the maximum num~r of

transmission attempts is tried).

Arm the system and fault one or more zones.

Silence alarm sounder(s) each time by entering the

code and pressing OFF. Check that Entry/Exit delay

zones provide the assigned delay times.

2. Check the keypad-initiated alarms, if

programmed in field “05, by pressing the Panic

keys (“ and #, 1 and

●, and/or 3 and #). If the

system has been programmed for audible

emergency, the console will emit a loud, steady

alarm sound. The word ALARM and a descriptor

“99- will be displayed for

● and #. (if 1 and ● are

pressed, a ’95” will be displayed; if 3 and # are

pressed, a “96” will be displayed).

Silence the

alarm by entering the security code and pressing

OFF. If the system has been programmed for silent

panic, there will be no audibie alarms or displays. a

report will be sent to the central station, however.

3. Notify the central station that all tests are

finished and verify results with them.

TURNING THE

SYSTEM

OVER TO THE USER

1. Fully explain the operation of the system to the

user by going over each of ita functions as well as

the User’s Manual supplied.

2. In particular, explain the operation of each

zone (entry/exit, perimeter, interior, fire, etc.).

Be sure the user understands how to operate any

emergency feature(s) programmed into the system.

IMPORT ANTI: In the spaces provided in the

Users Manual, record the Entry and Exit Delay

time6,

and those functions that have been

programmed into the available paira of PANIC keys

(* and #, 1 and

●, 3 and #).

3. Make sure the user understanda the importance

of testing the system at least weekly, following the

procedure provided in the User’s Manual.

-16-

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 24 25 26

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 5130XM Bedienerhandbuch Seite 18

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 5130XM