ADEMCO 4140XMP Spezifikationen PDF herunterladen (Seite 14)

IV. MOUNTING AND

MOUNTING

MoUNTING THE 4140XM? ‘PC BOAUO

POWERING THE SYSTEM

Before mounting the circuit bead ‘be cenain that the

~mpriate me~l kntiuw have been removed. DO NOT

A=MPT TO REMOVE THE KNOCKOUTS A~R ~E

CIRCU~ SOARO HAs BEEN tNST~.

1. Hang the three mounting d~ on tkc miscd ~net tcbc.

Obcewe pm-r ctip orient~hn 10 avoid damage b the

chp when mouming ccrews are tghtencd and 10 avoid

pmbbms tih imetibn ad rmvd d the PC Wti.

2. Insen the top of the circuk bard into the sbts al the top

Of the ~inet. M* cenain that the ~ati rastc in the

sbts ind~td in ccep 2 de~il.

3. Swing the b~e of the bard itio the mounting c~is and

secure the bard to the cdinet whh the a~mpanying

ecmwc (as illutmtd in step 3 detail).

ADVISORY

Make -tiain that the mounting ~rew are reason~ly tght

~ insure that there is a gd ground rnnne~ion tieen the

PC bwd md the mnet. Ah, dress fmti wiring awW fmm

the micropmesso, (tinter) section of the PC tiad. The

=binet provides 2 Imps on its hft and right sidewalls for

anchoting field wiring using tie wrapt. These stew are

imptiam to minimtilng the rik d pnel RF intetierem with

televisbn rmption.

MOUNTING THE 4140XMP LOCK

1. Remove the Iti kno~om on the mntml tiinet rover.

Inseti the kcy imo the Iti. Postion the I* in the hole

recking Mnain that the latch till m~e mmaa wtih the

Ietch bm~et when the dwr is doccd.

2. While holding the 1A cteady, insen the retainer ctip into

the retainer slots. Position dip as illustrated in the

diagram m the nefi page to f~ltate e~ remwal.

T-

MOUNTING THE 4127 CONSOLE

1. Sepamte the rnnsoie from hs ba~plate by removing the

two swew fmm the mp and bttom edges.

2. Usa the ba~piate to mark the ~shiins on tk wall @r the

screw mounting holes and the cti~ut for the intetiam

wiring. Use wall ancbm for the screwc md m~e the M-

out in the wall no larger than indimted on the template.

me backplate k designed to be direaiy moumed to ether

a single or double gang eldfical bx.

3. Pull the intetiace wiring in the wall through the c~-ut.

4. Pass the inteda- wiring through the opening in the

b~late, then mount the ba~plate to the wall sutiace

wtih screws.

5. Splice the intetiace wiring to the wnsole wires. Insulated

solderle= w;re splims (eg, Ademm311 ) may be used for

splicing.

6. Attach the main kdy of the mnsole to the wall-mounted

ba~plate. The rnnsole is properly attached when it is

screwed to the ba~plate by the top and bottom screws

previously removed.

-14-

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 51 52

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 4140XMP Spezifikationen Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 4140XMP