ADEMCO VISTA-250FBP Einstellungsanleitung Seite 31
- Seite / 136
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Section 3 - Installing the Control
3-9
+
-
-
+
-
+
•
EOL
POWER
SUPERVISION
RELAY
MODULE
EOLR-1
4-WIRE SMOKE
DETECTORS
2000
OHM
EOLR
HEAT
DETECTOR
+
–
BLK
+
-
ZONE
TERMINALS
(15-27)
12
11
10
9
N.O.
POLE
N.C.
Aux. Pwr 1
CONTROL
P
ANEL
•
SHOWN POWERED.
RELAY OPENS WHEN
POWER IS LOST
AUXILIARY RELAY
8
7
+
Keypad Prt 1
4_wiresmk-005-V0
Figure 3-9: Wiring Auxiliary Relay for Smoke Detector Reset
Telephone Line Connections
The VISTA-128FBP/VISTA-250FBP provides one main built-in dialer for communication to the central station and one
optional 5140DLM Backup Dialer, both supervised for voltage and current on the phone lines.
Do not connect the system to telephone lines that require ground start service.
U
L
For Listed fire central station (UL864/NFPA 72) applications, use communications device 7845i-ent alone, the
main dialer with the
7845i-ent or use the main dialer with the 5140DLM.
For listed fire remote station (UL864/NFPA 72) applications, use the main dialer with the 5140DLM.
Telephone line supervision is required for commercial fire alarm systems.
Main Dialer Connections
To connect the main dialer, refer to the Summary of Connections diagram and perform the following steps:
Step Action
1 Connect the main dialer to the telephone company lines using the RJ31X cable supplied.
2 If the dialer output is connected to telephone lines that have a telephone company MTU installed, cut the
blue jumper (W6).
Installing the 5140DLM Backup Dialer
Do not connect the main dialer and the backup dialer to the same telephone company line.
To install the 5140DLM, refer to the Summary of Connections diagram and perform the following steps:
Step Action
1 Mount the 5140DLM to the main PC board shield.
2 Connect the backup dialer to the telephone company lines using the RJ31X cable supplied.
3 Connect the backup dialer to the J3 connector on the main PC board using the ribbon cable (supplied with
the module).
4 Connect the earth ground screw on the 5140DLM to the earth ground terminal (30) on the main PC board
using 16AWG wire.
5 If the dialer output is connected to telephone lines that have a telephone company MTU installed, cut the
blue jumper on the 5140DLM PC board.
Telephone Line Supervision
If the tip/ring voltage falls below approximately 25 volts (13 volts if the blue jumper is cut) or the handset current is less
than approximately 10mA, the supervision circuits for the dialer output will indicate a fault condition. Faults on the
phone lines are displayed as zones 974 (main dialer) and 975 (backup dialer).
• To prevent risk of shock, disconnect the phone lines at the telco jack before servicing the panel.
• If the communicator is connected to a telephone line inside a PABX, be sure the PABX has backup power
supply that can support the PABX for 24 hours (central station usage) or 60 hours (remote station usage).
Many PABXs are not power-backed up, and connection to such a PABX results in a communication failure if
- K0376V2 7/09 Rev. B 1
- Table of Contents 3
- List of Figures 6
- PRODUCT MODEL NUMBERS: 7
- General Requirements 9
- COMMUNICATIONS 12
- General Description 15
- YELLOW DATA 18
- GREEN DATA 18
- Partitioning 19
- COMMON LOBBY 20
- Installing the Control 23
- Commercial Fire Guidelines 24
- Installing the Keypads 25
- Device Programming 26
- #93 Menu 26
- Auxiliary Relay Connections 30
- Telephone Line Connections 31
- Main Dialer Connections 31
- 2000 OHMS 34
- Figure 3-11 35
- Zone Programming 37
- VPLEX-VSI 39
- Wireless Zone Expansion 40
- Programming 41
- #93 Menu Mode 41
- 5881-001-V0 42
- SWITCH (N.O.) 46
- Event Log Connections 48
- Connecting the Transformer 48
- Earth Ground Connections 49
- Battery 52
- BATTERY TABS 53
- MAIN PCB 53
- #93 Menu Mode Programming 56
- Section 4 – Programming 57
- MAIN MENU 57
- OPTIONS 57
- Zone Number Designations 58
- Polling Loop Supervision 61
- SECTION 3: 61
- Zone Input Type Definitions 62
- Programming for Communicator 63
- Programming Guide 65
- Report Code Programming 67
- Output Programming 75
- ✳16 for Waterflow and 78
- Scheduling Options 81
- Time Window Definitions 82
- Limitation of 85
- Access Schedules Programming 85
- #80 Scheduling Menu Mode 85
- Daily Open/Close Schedules 86
- Holiday Schedules 86
- Time-Driven Events 87
- 30=Auto bypass – Zone list 90
- 31=Auto unbypass – Zone list 90
- 42=Enable Access Window for 90
- Access group(s) 90
- 50=Off-Normal Reminder 90
- 1 91
- 2 91
- 3…8 91
- Temporary Schedules 92
- User Scheduling Menu Mode 94
- Downloading Primer 95
- Section 7 – Downloading 97
- Figure 7-1 98
- Setting the Real-Time Clock 99
- User Access Codes 101
- User 3 User 3 102
- Level 1 Level 4 102
- Master Oper B 102
- EXPLANATION 103
- Exiting the User Edit Mode 104
- Testing the System 105
- Burglary Walk-Test ( 106
- Armed Burglary System Test 107
- Trouble Conditions 108
- To the Installer 109
- Regulatory Agency Statements 111
- FCC PART 68 NOTICE 113
- Summary of System Commands 115
- Specifications 117
- Contact ID Codes 119
- Event Log Alpha Descriptors 120
- 4-3, 4-4 124
- 6-4, 6-2 125
- 6-4, 6-5 127
- WARNING: 135
- ÊK0376V2Š 136
- ÊK0376V2ŠÊK0376V2Š 136
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO VISTA-250FBP
(54 Seiten)
(64 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.158 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern