ADEMCO 5130XM Bedienerhandbuch PDF herunterladen (Seite 17)

CONTACT ID REPORTING

This is the only format that can identify all 64

protection zones by their unique zone (Contact) ID

numbers, and provides a l-digit event qualifier and

3-digit,

specifically defined event code.which

quickly identifies the condition being reported.’

Contact ID reports in DTMF (Dual Tone Multi-

Frequency @ 10 characters per second) and

responds to a 1400 Hz followed by 2300 Hz

handshake, and a 1400 Hz kissoff. This format also

uses checksum instead of two message verification.

A complete report takes under 3 seconds.

ADVISORY

Ademco’s new Contact ID reporting IS

capable of uniquely reporting eH 64

zones

of Information, as

well

openlngs and

closings for all 22 users, to central

stations equipped with the Ademco 685

receiver

using

software level 4.4 or

higher. 685 software levels below 4.4

cannot support Contact ID reportlng. For

lnformatlon regardlng updatlng the 685

receiver, contact Ademco’s Technlcal

Support group at l-800-645-7492.

VII., PROGRAMMING THE SYSTEM

The system is shipped with a set of pre-

programmed values that are. designed to meet the

needs of many installations. These can be changed

by the installer to suit specific needs if desired. In

addition, four

sets of

pre-programmed

communication default values can also be loaded by

the installer, each set designeo for a specific

communication format. These too can be changed to

suit the needs of a particular installation.

There ‘are five sets of pre-programmed defaults

Changes to these pre-programmed values can be

programmed directly from the keypad or from a

computer terminal using the 413OPC Downloading

software, an IBM compatible computer and a HAYES

1200 SMARTMODEM. The following paragraphs

describes how to load the various default

programming sets.

For instructions on making

changes to particular programming fields, or for

using downloading, refer to the

Technical Reference

Manual.

For alpha

Controls, English Language descriptions of

the zones and a custom installer message (which

appears when the system is ready to arm) can be

programmed.

Refer to the instructions in the

Technical Refenmce Manual

for details.

The programming fields are grouped into two sets

of addresses. The first set is accessed as soon as

programming mode is entered. To access the

second set of addresses (indicated on the

programming form by a -1. in front of the 2-digit

field address), press ‘94 while in programming

mode.

To return to the first set of addresses,

press l 99.

To program specific data fields, press I’] plus the

2digit field address, then make the required entry.

The console will beep when a field has been

completely programmed and will automatically

display the next data field in numerical order.

To view .the contents of a data field, press [#] plus

the 2-digit field address. The field’s entries will be

displayed, but no changes to these entries can be

made.

available (one standard, plus four different

tiotimunication defaults). Any one of these can be

loaded into the system’s memory by doing the

following:

1. Enter programming mode by pressing [‘I and

[#] at the same time and within 30 seconds

after power is applied. OR Enter the installer

code, and press CODE + [O] +[O].

2. Load one of the default programming sets by

entering one of the following code sequences:

Loads standard defualt values.

Standard Low Speed 3+1/4+!

‘94’82 Ademco High Spee&

‘94’83

Expanded 4+2

A complete list of the default values can be found in

the Technical Reference Manual.

To Exit programming mode, press either l 98 or

l 99. Use

‘98 to prevent re-access to

programming mode by installer code method. ‘99

allows installer code access to programming mode.

- 15 -

WWW.DIYALARMFORUM.COM

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 29 30

WWW.DIYALARMFORUM.COM 1
004-000 27

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO 5130XM Bedienerhandbuch Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO 5130XM