ADEMCO VISTA-48D Spezifikationen PDF herunterladen (Seite 6)

Installation and Setup Guide

1-2

Compatible Devices

UL NOTE: For UL installations, use only UL Listed devices wherever compatible peripheral devices

are noted in these instructions.

• Supports up to 8 Addressable Keypads: 6148/6150 Fixed-Word Display Keypads, 6164 Alpha

Keypad, 6128RF/6128RFH/6150RF/6160RF Keypad/Transceivers, 6160V Voice Keypad

• Supports up to two (2)

Touch Screen (AUI) Devices (Symphony, 6270), which are in addition to the

standard eight (8) addressable keypads.

• Supports up to five 4219, 4229 addressable basic wired zone expander modules

• Supports 5881/5882EU/5882EUH/5883 series receiver and 5800/5800EU/5800H/5800AP series

transmitters

• Outputs from up to 16 relays, two on-board triggers, and/or Powerline Carrier Devices (X-10 type)

-- Use any combination of 4204, 4229, 6164 relays and/or Powerline Carrier Devices.

-- Output functions (up to 48)

• Alarm power output provides a 12VDC, 2 AMP (600mA max for UL) output that can drive

compatible sounders with a steady output for burglary/panic, or temporal pulse (3 pulses – pause –

3 pulses – pause – 3 pulses. . .) for fire. Uses current limiting circuitry for protection.

• Auxiliary Power Output: 12VDC, 600 mA max. (500mA max. for UL); all outputs are power limited.

• Backup Battery: Rechargeable (sealed lead-acid type) 12VDC, 4AH minimum (See Table on page 2-5,

Output Limitations to Meet CSFM 24-hour Battery Backup Requirements and UL Residential Fire

Installations)

• Audio Alarm Verification (using AAV module, such as ADEMCO UVS); can be used in conjunction

with an output trigger to permit voice dialog between an operator at the central station and a

person at the premises.

• Alternative Communication Media: Primary telephone number messages can be reported via ECP

connection to Ethernet TCP-IP Internet

• AC Power Supply: Wired-in or Plug-in 110 (e.g 1321)/220VAC transformer (220VAC not for UL

installations)

Important Installation Highlights (Installer Please Read)

• This system uses addressable keypads and Zone Expander Modules (see table of addresses in

Programming Overview section).

• Keypads must be set for addresses 16-23 (first keypad is address 16, which is different from

previous controls) and programmed in data fields *190-*196.

• Zone Expander Modules must be set for specific addresses (07-11), based on the zone numbers used

(see table of addresses in 4219/4229 Expansion Zones section).

• 4204 Relay Modules must be set for specific addresses (12-15; see Connecting Relay Modules

section).

• 6164 Keypads must be set for two addresses: a keypad address and a zone expander address (if

using the keypad’s expansion zones).

• This control will not power-up unless AC mains is connected (will not power-up on battery alone).

However, once the system is powered up, it will operate on battery power in case of AC mains loss.

• Relays have two programming menu modes: Use *79 Menu mode to map module addresses and

device (output) numbers. Use *80 Menu mode to define the output functions (see Output Device

Programming section).

• This system supports programmable function keys. Use *57 Menu mode to define the function keys

(see Function Key Programming section).

• This system provides various paging features. Refer to the Programming Overview section for a

summary on pager programming.

1 2 3 4 5 6 7 8 9 10 11 ... 79 80

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO VISTA-48D Spezifikationen Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO VISTA-48D