ADEMCO VIA 30+ Bedienungsanleitung PDF herunterladen (Seite 3)

–3–

ADEMCO VIA-30PSE PROGRAMMING FORM

FIELD FUNCTION PROGRAMMED VALUES [ ] = Default Value

–––––––– ––––––––––––––– –––––––––––––––––––––––––––––––––

SYSTEM SETUP (*20-*27)

*20 INSTALLER CODE

Enter 4 digits, 0-9...[4] [1] [1] [1]

*21 QUICK ARM ENABLE

†

[0 = no]; 1 = yes

*22 RF SYSTEM TYPE

[0 = none]; 1 = 5700 (4281); 2 = 5800 (5881)

*23 FORCED BYPASS FUNCTION

†

[0 = none]; 1 = bypass open zones

*24 RF HOUSE ID CODE [0][0]

MUST enter (01-31) for 5700 System. Enter also for 5827 Keypad

*25 WIRED EXPANSION/RELAY USED

†

[0 = none]; 1 = 4219; 2 = 4229; 3 = 4204

or 5827BD Keypad.

*26 VOICE MODULE ACCESS CODE

1st digit: Enter 1–9; 2nd digit: Enter only #+11 for '✴', #+12 for '#'.

[0] in either position = disabled.

*27 OUTPUT TO LONG RANGE RADIO

†

[0 = no]; 1 = yes. If yes selected, dialer reports to PRIMARY No. (field

*47) will also be sent via LRR. All dialer and LRR reports will be in Contact

ID format (overriding field *46 selection).

ZONE SOUNDS AND TIMING (*28-*39)

*28 SINGLE ALARM SOUNDING/ZONE

†

[0 = no]; 1 = yes

*29 FIRE SOUNDER TIMEOUT

†

[0 = fire sounder timeout]; 1 = no fire sounder timeout

*30 ALARM BELL TIMEOUT

†

0 = none; [1= 4 min]; 2 = 8 min; 3 = 12 min.; 4 = 16 min.

*38 ENTRY DELAY

†

0 = 0 sec ; 1= 20 sec; [2 = 30 sec]; 3 = 45 sec; 4 = 60 sec; 5 = 90 sec

EXIT Delay = ENTRY Delay + 15 sec

*39 AUDIBLE EXIT WARNING

†

0 = no; [1 = yes]

DIALER PROGRAMMING (*40-*50) In fields *40, *41, *42, enter up to the number of digits shown. Do not fill unused spaces.

Enter 0-9; #+11 for '✴'; #+12 for '#'; #+13 for a pause.

*40 PABX ACCESS CODE

Enter up to 4 digits.

If fewer than 4 digits entered, exit by pressing ✴ (and press 41, if entering next field). To clear entries from field, press ✴40 ✴.

*41 PRIMARY PHONE No.

Enter up to 12 digits.

If fewer than 12 digits entered, exit by pressing ✴ (and press 42, if entering next field). To clear entries from field, press ✴41 ✴.

*42 SECONDARY PHONE No.

Enter up to 12 digits.

If fewer than 12 digits entered, exit by pressing ✴ (and press 43, if entering next field). To clear entries from field, press ✴42 ✴.

*43 SUBSCRIBER ACCT No.

Enter 0-9; #+11 for B; #+12 for C; #+13 for D;

#+14 for E; [#+15 for F]. Enter ✴ as 4th digit, if 3+1 dialer reporting is to be used.

If only 3 digits used, exit by pressing ✴(and press next field). To clear entries from field, press ✴43 ✴.

Examples:

For Acct No. 1234, enter: 1234

For Acct No. B234, enter: #+11 2 3 4

For Acct No. 123, enter: 1 2 3 ✴

*45 PHONE SYSTEM SELECT

†

If Cent. Sta.

IS NOT

on a WATS line: [0 = Pulse Dial]; 1 = Tone Dial

If Cent. Sta.

a WATS line: 2 = Pulse Dial ;3 = Tone Dial

*46 REPORT FORMAT

Also see field *27.

[0 = 3+1, 4+1 ADEMCO L/S STANDARD]

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

6 or undefined = 4+2 ADEMCO EXPRESS

7 = ADEMCO CONTACT ID REPORTING

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

*47 SPLIT/DUAL REPORTING [0 = Disable (Backup report only)]

TO PRIMARY PHONE No. TO SECONDARY PHONE No.

1 =Alarms, Restore, Cancel Other Reports

2 =All Reports except Open/Close, Test Open/Close, Test

3 =Alarms, Restore, Cancel All Reports

4 =All Reports except Open/Close, Test All Reports

5 = All Reports (

Dual Reporting)

All Reports

A 10-digit code is sent to the pager consisting of

a 4-digit Subscriber #, a 3-digit Event code, & a

3-digit User or Zone #. See Installation

Instructions for an explanation of the 10-

digit code.

TO PRIMARY PHONE No. TO PAGING No.* (SECONDARY)

6 = All reports except Open/Close ** Alarms, Open/Close, Troubles

7 = All reports ** Alarms, Troubles

8 = All reports ** Alarms, Open/Close, Troubles

9 = All reports except Open/Close ** Alarms, Open/Close for Users 5 –

25, Troubles

* Can only be used if Primary reporting is Ademco Contact ID.

†

Entry of a number other than one specified will give unpredictable results.

1 2 3 4 5 6 7 8 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

ADEMCO VIA 30+ Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme ADEMCO VIA 30+